BIG BALE Transtacker Extra Скачать руководство пользователя | Manualshive

Страница: 13 / 36

background image

5.0

Operation

5.5

Controls Cont..

6. Drive along side the first bale. (Select a bale that is on

flat ground). Drive forward until the guide is pushing the

bale along the ground and having turned towards the bale, it

should be tight against the pickup rails

(Fig. 20).

Fig. 20 Note 1

The bales should come to rest firmly against the guide.

Fig. 20 Note 2

Turning towards the bale as you pass it will ensure the bale

is kept tight against the guide rails.

1. Drive close along side the bales (it may be beneficial to

turn into the bale as the tractor passes, to ensure the bale

fits tight against the pickup rails), when the bale is in the

correct position, push forward on the joystick

(Fig. 21)

. The

machine will automatically pick up the bale and place it on

the table, before returning to its original position

(Fig. 22)

.

Caution:

It is important that the tractor engine is turning fast

enough to maintain a full flow of oil to the machine during

automatic cycles. Select a gear that is best suited to engine

rpm and the distance between the bales. There is no

theoretical limit to the speed at which bales can be picked

up but some damage to bales may occur above (6 mph)

10kph.

13

1

2

Fig. 20

5.6

Pickup (Automatic)

Fig. 22

Fig. 21

«
...
11
12
13
14
15
...
»

Содержание Transtacker Extra





































Отзывы:

Нет отзывов

Похожие инструкции для Transtacker Extra

Бренд: Handler Страницы: 25

Бренд: Wahl Страницы: 47

Бренд: LA Audio Страницы: 9

Бренд: Zimmer Страницы: 2

Бренд: ZipRip Страницы: 31

Бренд: Marcy Страницы: 9

Бренд: Fagor Страницы: 92

Wallach UltraFreeze

Бренд: Cooper Surgical Страницы: 4

Бренд: SDE Lighting Страницы: 7

Bug Zappers BZ-15

Бренд: Black Flag Страницы: 2

CLIMBING ADVENTURE

Бренд: LAPPSET Страницы: 75

Powerhouse PL513

Бренд: X10 Страницы: 12

Бренд: EFILive Страницы: 39

Бренд: Vascular Страницы: 64

ECO-MASTER 300 l

Бренд: Garantia Страницы: 2

Бренд: CAMP Страницы: 156

Бренд: Datex-Ohmeda Страницы: 150

Бренд: QTAC Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды