BIG BALE Transtacker Extra Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 36

background image

5.0

Operation

21

5.14

Operation as a Bale Transporter

WARNING:

Keep persons away from the machine during

operation. There is a danger from falling bales and moving

machinery.

WARNING:

When the pickup guide is out there is a danger

that it may be overlooked by the operator. A flashing light on

the control box indicates the guide is out. An indicator on

the pickup latch signals that the guide is in and the pickup is

locked in position.

WARNING:

Keep clamp side pins in place when

transporting on highways. When travelling along roads the

side clamps are subject to variable and high loads. Failure

or inadvertent operation of the side clamps could cause

very serious injury or damage to others.

WARNING:

Failure of the hydraulic lines is covered by the

load valves attached to the clamp and lift cylinders. Road

Mode should be used during transport to prevent

inadvertent operation. The safety pins provide a necessary

and useful further safety device, should there be a cylinder

failure.

WARNING:

Take care when operating on sloping ground or

when traversing undulations at speed to prevent overturning

of the stacker. By necessity the machines have a high

centre of gravity when loaded. Caution should always be

exercised to prevent overturning and resulting injury and/or

damage.

WARNING:

Do not raise the platform of the Transtacker

while under high voltage power lines. Some parts of the

machine can exceed 5.2m high and cause electrocution

and/or fire.

5.13

Finishing a Stack Cont.

9. Press and hold the ‘Road Mode’ button to retract the

guide. Ensure the flashing

GUIDE

LED is extinguished

and/or the pickup is locked and the indicator shows the

guide is in i.e. pointing to the yellow sector (

Fig. 57

).

WARNING:

Take care when operating on sloping ground or

when traversing undulations at speed to prevent overturning

of the Transtacker. By necessity the machine has a high

centre of gravity when loaded. Caution should always be

exercised to prevent overturning and resulting injury and/or

damage.

Fig. 57

Yellow Sector

«
...
19
20
21
22
23
...
»

Содержание Transtacker Extra





































Отзывы:

Нет отзывов

Похожие инструкции для Transtacker Extra

Бренд: ABB Страницы: 36

Бренд: ABB Страницы: 40

Бренд: NEC Страницы: 54

Бренд: Quincy lab Страницы: 4

Бренд: Abbott Страницы: 2

FreeStyle Libre

Бренд: Abbott Страницы: 3

Бренд: abc Страницы: 8

Бренд: ParaBody Страницы: 5

Бренд: Baileigh Industrial Страницы: 28

Бренд: Baileigh Industrial Страницы: 56

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 20

Бренд: Fellowes Страницы: 20

Бренд: iFIT Страницы: 11

Бренд: Keller Страницы: 12

Бренд: MacDon Страницы: 49

Бренд: MacDon Страницы: 49

Бренд: MacDon Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды