Big Backyard F23475 страница 43 Скачать руководство пользователя

Страница: 43 / 60

Bolts

Hardware

Front Beam 2 x 6 x 94"

4X Triangle Plate

Back Beam 2 x 6 x 94"

Tighten

Hex Bolt 1/4 x 5½"

Swing Beam Assembly

E40

Hex Bolt 5/16 x 4"

Hex Bolt 5/16 x 4½"

D13

Wood Parts

Sw Post 2 x 4 x 92½"

Sw Support 5/4 x 4 x 48½"

Sw Upright 2 x 4 x 50½"

Hardware

C18

Wood Parts

Bolts

Tighten

Hex Bolt 5/16 x 1½"

WARNING!

STEP 28

Swing Assembly A

C18

E40

C18

D13

Swing End Assembly

: Attach

(C18)

SW Post to

(D13)

SW Upright using 2

(G4)

5/16 x 4” hex bolts (with flat washer, lock washer

and t-nut).

: Attach

(E40)

SW Support to

(D13)

SW Upright and

both

(C18)

SW Posts using 3

(G5)

5/16 x 4½” hex bolts

(with flat washer, lock washer and t-nut).

Top

Bottom

: Attach 2 Triangle Plates to

(C1)

Front Beam and 2 Triangle Plates

(C2)

Back Beam using 1

(G1)

5/16 x 1½” hex bolt (with flat

washer, lock washer and t-nut) per Triangle Plate in the correct holes
as shown below. The holes marked with an “X” will not be used.

: Install 2

(H7)

1/4 x 5½” hex bolts (with flat washer, lock washer

and t-nut) into both

(C1)

Front Beam and

(C2)

Back Beam. These

bolts do not attach to anything but must be used on the ends of the
beams to prevent checking and splitting of wood.

*Must Use on
the ends of the
beams to prevent
checking and
splitting of wood.

Fort End

No overhang

Top

Bottom

Top

Swing End Side

with overhang

Bottom

Make sure l.D Label with 800 number
shows on opposite side.

Содержание F23475





























































Результаты поиска

Содержание F23475

Отзывы:

Похожие инструкции для F23475

Бренды по названию

Популярные бренды

Big Backyard F23475, Инструкция по установке и эксплуатации

Результаты поиска

Содержание F23475

Отзывы:

Похожие инструкции для F23475

Бренды по названию

Популярные бренды