Big Backyard F23475 страница 42 Скачать руководство пользователя

Страница: 42 / 60

STEP 27

Attach Ladder

Wood Parts

w/ hardware (pkg of 2)

1X Corner Brace

1/4 x 1½” lag screws (with flat washer) per hand grip.

2X Hand Grip

(LS1)

(C4)

Lag Screw 1/4 x 1½"

Ground Access 1 x 6 x 37¾"

Center Divider using 2

Post and 1 to the

1 Hand Grip to the

(B18)

E18

Hardware

Hex Bolt 1/4 x 4"

Wood Screw #8 x 1½"

1X Assembled Access Ladder

: In the opening across from the Rock Wall attach the Access Ladder

(B20)

Back Floor using 2

(H4)

1/4 x 4” hex bolts (with flat washer,

lock washer and t-nut).

: Attach

(E18)

Ground Access to

(C8)

Ground Front Back using 2

Corner Braces with hardware.

: Attach

(E18)

Ground Access to the Access Ladder using 2

(S2)

x 1½” wood screws.

: Pre-drill using a 1/8” drill bit by using hand grips as a guide. Attach

LS1

Corner Brace
w/ hardware
X2

B11

Hand Grips

2 per Hand Grip

LS1

B20

E18

B18

Содержание F23475





























































Результаты поиска

Содержание F23475

Отзывы:

Похожие инструкции для F23475

Бренды по названию

Популярные бренды

Big Backyard F23475, Инструкция по установке и эксплуатации

Результаты поиска

Содержание F23475

Отзывы:

Похожие инструкции для F23475

Бренды по названию

Популярные бренды