Big Backyard F23475 Скачать руководство пользователя страница 18

Страница: 18 / 60

STEP 2

Access Ladder Assembly

Drill 1/8" pilot holes
through Dowels to
prevent splitting wood

Make sure shoulder is
against rails before drilling

S3 Wood Screw #8 x 2½"

Tennon Dowel 1

x 18

Wood Parts

Before Fastening

using 4

Ladder Bottom 5/4 x 4 x 20"

Hardware

Wood Parts

#8 x 2½” wood screws.

Wood Screw #8 x 2½"

Ladder Bottom to the access rails

B12

B11

(S3)

Square Assembly

Left Access 2 x 4 x 69"

Right Access 2 x 4 x 69"

: Attach

E12

(E12)

Hardware

: Insert

(A3)

Tenon Dowel into both

(B11)

Left Access and

(B12)

Right

Access making sure the shoulder is snug against the rails. Pre-drill with
1/8” drill bit through

(B11)

Left Access and

(B12)

Right Access and into

each dowel.

: Use 2

(S3)

#8 x 2½” wood screws per dowel to attach dowels to rails.

B12

B11

WARNING!

B12

B11

E12

Note:

(E12)

Ladder Bottom must

be flush with

(B11)

on this side

Содержание F23475





























































Результаты поиска

Содержание F23475

Отзывы:

Бренды по названию

Популярные бренды

Big Backyard F23475, Инструкция по установке и эксплуатации

Результаты поиска

Содержание F23475

Отзывы:

Бренды по названию

Популярные бренды