Big Backyard F23475 Скачать руководство пользователя страница 21

Страница: 21 / 60

Hardware

B20

Hex Bolt 1/4 x 2¾"

shown below using 4

(H13)

Hex Bolt 1/4 x 3½"

B19

: Make sure the fort is square and then tighten all bolts.

Back Floor 2 x 4 x 83

Front Floor 2 x 4 x 83

Ground Front Back 1 x 6 x 92½"

lock washer and t-nut) per board. Notice the boards extend past

1/4 x 3½” hex bolts (with flat washer,

the Slide Wall side.

Wood Parts

H11

: Attach both the

(B19)

Front Floor and

(B20)

Back Floor

between each Wall Assembly using 2

(H11)

1/4 x 2¾” hex bolts

(with flat washer, lock washer and t-nut) per board. Notice the
hole locations of each board.

: Attach both

(C8)

Ground Front Back to both Wall Assemblies as

H13

1X Swing Wall Assembly
1X Slide Wall Assembly

Slide Wall Assembly

H11

B19

Swing Wall Assembly

H11

H13

B20

Notice hole
locations

Use Help Square Assembly Tighten Bolts

STEP 6

Assemble Fort Frame

Содержание F23475





























































Результаты поиска

Содержание F23475

Отзывы:

Бренды по названию

Популярные бренды

Big Backyard F23475, Инструкция по установке и эксплуатации

Результаты поиска

Содержание F23475

Отзывы:

Бренды по названию

Популярные бренды