Big Backyard F23475 Скачать руководство пользователя

Страница: 44 / 60

STEP 29

Swing Assembly B

GL8

Swing End Side

Side with OVERHANG

Lock Nut

Swing End Assembly

Fort End

NO OVERHANG

Make sure Swing End
Flares out 105°

105

B33

: Attach

(C44)

SW Rail Block between the

(C1)

Front Beam and

(C2)

Back Beam using 1

(G5)

5/16 x 4½” hex bolt (with flat washer,

lock washer and t-nut).

: Connect the swing beam side with the Triangle Plates over

hanging to the Swing End Assembly using 1

(G5)

5/16 x 4½” hex

bolt (with flat washer, lock washer and t-nut) and 1

(GL8)

5/16 x 2”

hex bolt (with 2 flat washers and 1 lock nut) as shown below.

: Make sure the Swing End flares out at a 105 degree angle.

Back Beam Assembly

Front Beam Assembly

Hardware

Hex Bolt 5/16 x 4½"

Hex Bolt 5/16 x 2"

GL8

1X Front Beam Assembly
1X Back Beam Assembly
1X Swing End Assembly

Wood Parts

1X B33 SW Rail Block 2 x 4 x 5

Содержание F23475





























































Результаты поиска

Содержание F23475

Отзывы:

Похожие инструкции для F23475

Бренды по названию

Популярные бренды

Big Backyard F23475, Инструкция по установке и эксплуатации

Результаты поиска

Содержание F23475

Отзывы:

Похожие инструкции для F23475

Бренды по названию

Популярные бренды