Big Backyard F23475 Скачать руководство пользователя

Страница: 41 / 60

Hardware

Wood Screw #8 x 1½"

(S2)

Wood Parts

Rock Wall Ground to the Rock Wall

using 2

CE Wall Board 1 x 6 x 23½"

Pan Screw #12 x 2"

(E19)

Rock Wall Ground 1 x 6 x 38"

#8 x 1½” wood screws.

Move Fort to final location

: In the opening next to the picnic table, attach the Rock

Wall to the

(B19)

Front Floor using 1

(S7)

#12 x 2” pan

screw in each outside hole and 1

(S2)

#8 x 1½” wood

screw in each inside hole as shown below.

: Attach 1

(B1)

CE Wall Board to the top of the Rock

Wall using 4

(S2)

#8 x 1½” wood screws. Make sure that

(B1)

is tight against the top rock board.

: Attach

(E19)

Rock Wall Ground to

(C8)

Ground Front

Back using 2 Corner Braces with hardware.

: Attach

E19

1X Corner Brace

w/ hardware (pkg of 2)

Note: 1 Corner Brace on each side of

(E19)

B19

E19

Corner
Brace
X2

STEP 26

Attach Rock Wall

Содержание F23475





























































Результаты поиска

Содержание F23475

Отзывы:

Похожие инструкции для F23475

Бренды по названию

Популярные бренды

Big Backyard F23475, Инструкция по установке и эксплуатации

Результаты поиска

Содержание F23475

Отзывы:

Похожие инструкции для F23475

Бренды по названию

Популярные бренды