Big Backyard F23475 Скачать руководство пользователя

Страница: 50 / 60

STEP 3

Assemble Slide Sections

PB1

TNR Slide Right Flange

TNR Slide Left Flange

TNR Porthole

CORRECT

LN1

Inside

TNR Porthole

TNR Slide Elbow Half

TNR Slide Left Flange

Inside

INCORRECT

inside

sliding surface on the

provide a smooth

inward. This will

slide is not

Hardware

PB1

with contour facing

smooth!

1/4" Locknut

42X

Parts

TNR Porthole

TNR Slide Right Flange

42X

Pan Bolt 1/4 x 3/4"

Assemble Porthole

Porthole
contour facing
outward. Inside,

LN1

Attach TNR Slide Right Flange to TNR Slide Left

Flange using 6

(PB1)

1/4 x 3/4” pan bolts with 6

(LN1)

1/4” lock nuts.

Attach 2 TNR Slide Elbow Halves together with the

TNR port hole using 12

(PB1)

1/4 x 3/4” pan bolts with

(LN1)

1/4” lock nuts (8 on the long side and 4 on the

short side). Make sure to install the port hole as directly
in the diagrams below. Repeat this step twice more to
have 3 Elbow Assemblies.

PB1

X12

TNR Porthole

TNR Slide Elbow Half

LN1

X12

Содержание F23475





























































Результаты поиска

Содержание F23475

Отзывы:

Похожие инструкции для F23475

Бренды по названию

Популярные бренды

Big Backyard F23475, Инструкция по установке и эксплуатации

Результаты поиска

Содержание F23475

Отзывы:

Похожие инструкции для F23475

Бренды по названию

Популярные бренды