Big Backyard ASHBERRY II F23073C Скачать руководство пользователя страница 63

Страница: 63 / 80

[email protected]

Step 26: Attach Windows and Clock to Fort

Hardware

16 x

#6 x 5/8” Pan Screw

4 x

#8 x 1” Pan Screw

S13

Other Parts

2 x Arch Top Window
1 x Oval Window
1 x Clock Assembly

S10

On the Front Wall side of the assembly place 2 Arch Top Windows in the outside window gaps between (2145)

Back Top and (2125) Middle Front and attach to (1740) Window Braces, (2119) Oval Windows, (2145) Back Top

and (0389) Window Frame with 6 (S13) #6 x 5/8” Pan Screws per window. (fig. 26.1 and 26.2)

Place Oval Window in centre window gap and attach to both (2119) Oval Windows, (2145) Back Top and

(0389) Window Frame with 4 (S13) #6 x 5/8” Pan Screws. (fig. 26.2)

Place Clock Face between (2124) Front Floor and roof support detail snug to the siding. The hole in the clock

should line up to the hole in (2162) Siding - Clock. Attach with 4 (S10) #8 x 1” Pan Screws. (fig. 26.1 and 26.3)

From inside the assembly insert Clock Knob in the hole in (2162) Siding - Clock, then with 1 person inside the

fort and 1 outside place Hour Hand over Clock Knob making sure they are lined up properly. Finally, press Minute

Hand over Hour Hand. (fig. 26.3, 26.4, 26.5 and 26.6)

Fig. 26.1

x 4

Front Wall

2145

Fig. 26.2

Fig. 26.3

Fig. 26.4

1740

2119

1740

0389

2125

S13

x 6

S13

x 6

Oval Window

Inside View

2124

2162

Hole in clock

siding lines up to

hole in clock.

2162

Knob connects to

minute/hour hands.

S10

x 4

2124

2153

Clock

Arch Top Window

Hour Hand

Minute Hand

Fig. 26.5

Knob

Clock

Hour Hand

Minute Hand

Arch Top

Window

Содержание ASHBERRY II F23073C

















































































Результаты поиска

Содержание ASHBERRY II F23073C

Отзывы:

Похожие инструкции для ASHBERRY II F23073C

Бренды по названию

Популярные бренды

Big Backyard ASHBERRY II F23073C, Инструкция по установке и эксплуатации

Результаты поиска

Содержание ASHBERRY II F23073C

Отзывы:

Похожие инструкции для ASHBERRY II F23073C

Бренды по названию

Популярные бренды