Big Backyard ASHBERRY II F23073C Скачать руководство пользователя страница 49

Страница: 49 / 80

[email protected]

Tight to the top of (2123) Back Floor and flush to the outside edge of (2112) SL Post attach (2151) Back Wall

Support to (2112) SL Post and (2153) Post with 4 (S7) #12 x 2” Pan Screws. (fig. 17.1 and 17.2)

Flush to the outside edge of (2151) Back Wall Support and tight to the floor boards attach (1205) CE Access

Wall to (2151) Back Wall Support, (2143) Middle Back and (2145) Back Top with 5 (S1) #8 x 1-1/8” Wood Screws,

as shown in fig 17.2 and 17.4.

Evenly space and attach 4 (5265) Cedar Walls to (2151) Back Wall Support and (2143) Middle Back with 4

(S1) #8 x 1-1/8” Wood Screws, as shown in fig 17.1, 17.2, 17.3 and 17.4. Make sure the bottom of the boards

are tight against the floor boards and the bevelled ends are at the top and facing out.

Step 17: Upper Back Wall Assembly

Hardware

Wood Parts

4 x

Cedar Wall 1 x 4 x 28”

1 x

CE Access Wall 1 x 4 x 41-3/4”

1 x

Back Wall Support 5/4 x 4 x 31”

5265

21 x

#8 x 1-1/8” Wood Screw

4 x

#12 x 2” Pan Screw

Fig. 17.2

Back Wall

x 4

Fig. 17.1

Fig. 17.3

Fig. 17.4

Outside View

Back Wall

Outside View

Inside View

2112

2151

Flush

2153

Flush

2123

2145

2153

2143

2112

2151

1205

5265

x 5

1205

Inside
View

x 4 per

board

2151

Содержание ASHBERRY II F23073C

















































































Результаты поиска

Содержание ASHBERRY II F23073C

Отзывы:

Похожие инструкции для ASHBERRY II F23073C

Бренды по названию

Популярные бренды

Big Backyard ASHBERRY II F23073C, Инструкция по установке и эксплуатации

Результаты поиска

Содержание ASHBERRY II F23073C

Отзывы:

Похожие инструкции для ASHBERRY II F23073C

Бренды по названию

Популярные бренды