Big Backyard ASHBERRY II F23073C Скачать руководство пользователя страница 33

Страница: 33 / 80

[email protected]

Hardware

Wood Parts

10 x

1/4 x 2” Hex Bolt

(1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

Step 9: Front Wall Assembly

Part 2

Loosely attach 2 (2153) Posts and 2 (2154) Front Posts to (2150) Front Back Ground with 6 (H2) 1/4 x 2” Hex

Bolts (with lock washer, flat washer and t-nut), as shown in fig. 9.2. Notice where (2154) Front Post from Step 9,

Part 1 is attached and ensure that (2135) Wall Support faces the other (2154) Front Post.

Loosely attach (2114) Top Front to each post, with 1 (H2) 1/4 x 2” Hex Bolt (with lock washer, flat washer and

t-nut) per post. The distance between (2153) Post and (2154) Front Post with (2135) Wall Support must be 16-

5/8”. (fig. 9.2)

2 x

Post 2 x 4 x 96-1/2”

1 x

Top Front 1 x 4 x 52”

1 x

Front Post 2 x 2 x 94”

1 x

Front Back Ground 1 x 5 x 67”

2153

2154

2150

2114

2153

Fig. 9.2

1/4” lock

washer

1/4” flat

washer

Notice bevelled

edge facing up

1/4” t-nut

2154

2150

Notice position of

(2135) Wall Support

2135

16-5/8”

Содержание ASHBERRY II F23073C

















































































Результаты поиска

Содержание ASHBERRY II F23073C

Отзывы:

Похожие инструкции для ASHBERRY II F23073C

Бренды по названию

Популярные бренды

Big Backyard ASHBERRY II F23073C, Инструкция по установке и эксплуатации

Результаты поиска

Содержание ASHBERRY II F23073C

Отзывы:

Похожие инструкции для ASHBERRY II F23073C

Бренды по названию

Популярные бренды