Big Backyard ASHBERRY II F23073C Скачать руководство пользователя страница 27

Страница: 27 / 80

[email protected]

Step 6: Door Assembly

Part 1

3 x

Door Siding 3/8 x 3-1/2 x 11-3/8”

1 x

Door Siding Top 3/8 x 3-1/2 x 11-3/8”

Wood Parts

1 x

Door Side Right 1-1/4 x 3 x 40-1/8”

1 x

Door Side Left 1-1/4 x 3 x 40-1/8”

2 x

Door Cross 1/2 x 3-3/8 x 15-7/16”

1 x

Door Arch 1/2 x 4-1/2 x 15-7/16”

Hardware

18 x

#8 x 1-1/8” Wood Screw

10 x

#8 x 7/8” Truss Screw

2057

2053

2052

2058

2051

2050

Place 1 (2052) Door Cross flush to the bottom and outside edges of (2057) Door Side Right and (2058) Door

Side Left. (fig. 6.1)

Place the second (2052) Door Cross in the middle notches of (2057) Door Side Right and (2058) Door Side

Left, flush to the outside edges. (fig. 6.1)

Place (2053) Door Arch tight to the top notches of (2057) Door Side Right and (2058) Door Side Left, flush to

the outside edges. (fig. 6.1)

Make sure assembly is square then attach top, middle and bottom boards with 6 (S1) #8 x 1-1/8” Wood

Screws per board. (fig. 6.1)

Starting tight to the bottom (2052) Door Cross, and working up, evenly space 3 (2051) Door Siding then 1

(2050) Door Siding Top tight to the inside edges of (2057) Door Side Right and (2058) Door Side Left. (2050)

Door Siding Top should sit tight to the bottom of (2052) Door Cross. Attach each (2051) Door Siding with 2 (S0)

#8 x 7/8” Truss Screws per board and (2050) Door Siding Top with 4 (S0) #8 x 7/8” Truss Screws. (fig. 6.1)

Fig. 6.1

2058

Fig. 6.2

x 6

2053

Flush and tight

x 6

2050

2052

2051

x 10

2057

x 6

Содержание ASHBERRY II F23073C

















































































Результаты поиска

Содержание ASHBERRY II F23073C

Отзывы:

Похожие инструкции для ASHBERRY II F23073C

Бренды по названию

Популярные бренды

Big Backyard ASHBERRY II F23073C, Инструкция по установке и эксплуатации

Результаты поиска

Содержание ASHBERRY II F23073C

Отзывы:

Похожие инструкции для ASHBERRY II F23073C

Бренды по названию

Популярные бренды