Big Backyard ASHBERRY II F23073C Скачать руководство пользователя страница 31

Страница: 31 / 80

[email protected]

Overlap cedar roofing

2156

1-1/2”

Roof Supports

removed for clarity

Flush to edge

Step 8: Roof Assembly

Part 2

Starting at the top of the Roof Support Assembly attach 1 (2156) Roofing on each side of the Roof Support

Assemblies with 3 (S0) #8 x 7/8” Truss Screws per board. (fig. 8.2) Be sure to overlap the top of the boards so

there are no gaps. (fig. 8.2 and 8.3)

Drill a hole 1-1/2” up from the bottom of the 2 bottom (2156) Roofing (for bottom row only).

Attach 1 (2156)

Roofing at the bottom of the Roof Support Assembly on each side, making sure they are flush to each (2146) Roof

Support Right and (2132) Roof Support Left with 3 (S0) #8 x 7/8” Truss Screws per board. (fig. 8.2 and 8.4)

On one side of the assembly evenly space and attach 8 (2156) Roofing, leaving no gaps, with 3 (S0) #8 x 7/8”

Truss Screws per board. There should be 10 (2156) Siding on this side. (fig. 8.2)

On the other side of the assembly evenly space and attach 8 (2156) Roofing, leaving no gaps, with 3 (S0) #8 x

7/8” Truss Screws per board. (fig. 8.2)

Fig. 8.4

Wood Parts

Hardware

60 x

#8 x 7/8” Truss Screw

20 x

Roofing 3/8 x 3-1/2 x 53-13/16”

2156

Fig. 8.2

Fig. 8.3

2132

2146

1-1/2”

x 60

2156

x 20

2161

(hidden)

Содержание ASHBERRY II F23073C

















































































Результаты поиска

Содержание ASHBERRY II F23073C

Отзывы:

Похожие инструкции для ASHBERRY II F23073C

Бренды по названию

Популярные бренды

Big Backyard ASHBERRY II F23073C, Инструкция по установке и эксплуатации

Результаты поиска

Содержание ASHBERRY II F23073C

Отзывы:

Похожие инструкции для ASHBERRY II F23073C

Бренды по названию

Популярные бренды