Big Backyard ASHBERRY II F23073C Скачать руководство пользователя страница 52

Страница: 52 / 80

[email protected]

Hardware

Wood Parts

15 x

#8 x 7/8” Truss Screw

6 x

#8 x 1-1/2” Wood Screw

1 x

Window Frame 1 x 2 x 16-1/4”

1 x

Narrow Siding 3/8 x 3 x 29-5/16”

1 x

Trim 5/8 x 1-3/4 x 16-1/4”

4 x

Siding 3/8 x 3-1/2 x 29-5/16”

Step 19: Lower Front Wall Assembly

Part 1

Flush to the outside edge of (2154) Front Post and tight to the top of (2150) Front Back Ground attach (0389)

Window Frame to (2154) Front Post with 3 (S2) #8 x 1-1/2” Wood Screws. (fig. 19.1 and 19.2)

Flush to the top and tight to the inside edge of (0389) Window Frame attach (2160) Narrow Siding to (2135)

Wall Support, (2154) Front Post and (2153) Post with 3 (S0) #8 x 7/8” Truss Screws as shown in fig. 19.3.

Tight to bottom of (2160) Narrow Siding and tight to (0389) Window Frame attach 4 (2159) Siding to (2135)

Wall Support, (2154) Front Post and (2153) Post with 3 (S0) #8 x 7/8” Truss Screws per board, as shown in fig.

19.1 and 19.3. Make sure there are no gaps between boards. The bottom (2159) Siding will be tight to the top of

(2150) Front Back Ground.

Tight to siding and top of (2150) Front Back Ground attach 1 (2133) Trim to (2153) Post with 3 (S2) #8 x 1-1/2”

Wood Screws. (fig 19.3)

0389

Outside View

Fig. 19.3

Fig. 19.1

2160

2135

2154

2153

2133

2150

2159

x 3

x 3 per board

2160

2133

2159

Fig. 19.2

Flush

2150

2154

0389

Flush

Tight

Содержание ASHBERRY II F23073C

















































































Результаты поиска

Содержание ASHBERRY II F23073C

Отзывы:

Похожие инструкции для ASHBERRY II F23073C

Бренды по названию

Популярные бренды

Big Backyard ASHBERRY II F23073C, Инструкция по установке и эксплуатации

Результаты поиска

Содержание ASHBERRY II F23073C

Отзывы:

Похожие инструкции для ASHBERRY II F23073C

Бренды по названию

Популярные бренды