background image

OPERATION MANUAL       

                                                             

 

 

 

 

10. As soon as the threading board is almost all the way through  
      the laminator push approx. 2 cm of the picture under the  
      threading board.  

      ATTENTION: Make sure that you leave enough print cut 
      edge when printing the picture! 

 
11. Allow the threading board to continue to carry the film through

 

      the rollers. As soon as the threading board is out the back of  
      the laminator lower the top roller (6) and adjust the pressure  
      according to the thickness of the picture (see p.12). 
 

      ADVICE: At the beginning it is very important to feed      
      the picture

 

in correctly, it must be parallel to the rollers.  

      For this reason do not feed in the picture directly after  
      the threading board but start with an envelope made of  
      silicone release paper (approx. 10 cm deep and at least  
      as wide as the laminating film) with the silicone coating   
      facing inwards. Run the envelope between the rollers  
      until only 2-3 cm of the envelope remain visible. Push the 
      picture in the envelope and adjust it. The advantage of  
      this procedure is that the picture does not stick to the  
      lamination film, this makes it possible to adjust it 
      correctly! 
 

 

 

Advice for the laminating of  
long pictures 

 
When laminating pictures longer than 1 m it is recommended to 
work as follows: 
 
1. Wind up the picture on an empty core. 
 
2. Load the core onto the bottom supply shaft (13).  
    

ATTENTION: When fixing the cones take care that the core 

    has play to the right and left side! 

 
3. Insert the picture underneath the switching axis (9) and run the 
    picture through the rollers. 
 
This kind of handling makes it possible that the picture is pressed 
earlier and stronger against the bottom roller which avoids the 
occurrence of a “wave” in the middle of the picture. 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

Picture 8 
Switching axis

 

 

 

 

 

 

 
 

Manual 

Roll

Lam 120W; 

Roll

Lam 140W; 

Roll

Lam 160W                                                        24 

Содержание RollLam 120C


































Отзывы: