BETTCHER INDUSTRIES Whizard Quantum Air 1000 Скачать руководство пользователя страница 44

Страница: 44 / 183

BETTCHER

Industries, Inc.

Instructions for Operation

4-20

Instructions for Operation
Whizard Quantum

Air Operating Instructions and Parts

List

Manual No. 102481
April 17, 2015

Blade Changing

Sharp blades may cause cut injury!

For proper protection of hands, a protective glove
should be used when operating this equipment and
during the handling of blades.

Always disconnect the tool from the air supply prior
to servicing.

The Bettcher Quantum

Air Trimmers have been designed to allow the blades to be quickly

removed and reinstalled.

To Change the Blade

•

Loosen only the left cover retaining screw.

NOTE

Slight tension on the left cover screw will allow the blade housing to stay open.

•

Holding the tool blade side up, pry
open the blade housing with a
screwdriver.

•

Carefully remove the old blade.

•

Insert a new blade in the housing.

WARNING

Housing Slot

Screwdriver

Pivot Support
Point

Left Cover
Retainging Screw

Содержание Whizard Quantum Air 1000
























































































































































































Результаты поиска

Содержание Whizard Quantum Air 1000

Отзывы:

Похожие инструкции для Whizard Quantum Air 1000

Бренды по названию

Популярные бренды

BETTCHER INDUSTRIES Whizard Quantum Air 1000, Инструкция по эксплуатации и перечень запасных частей

Результаты поиска

Содержание Whizard Quantum Air 1000

Отзывы:

Похожие инструкции для Whizard Quantum Air 1000

Бренды по названию

Популярные бренды