BETTCHER INDUSTRIES Whizard Quantum Air 1000 Скачать руководство пользователя страница 116

Страница: 116 / 183

BETTCHER

Industries, Inc.

Maintenance

5-70

Maintenance
Whizard Quantum

Air Operating Instructions and Parts

List

Manual No. 102481
April 17, 2015

Quick Start Valve and Hose Assembly Maintenance

Required Tools for Quick Start Valve and Hose Assembly
Maintenance

1 – 1/2” Open End Box Wrench
1 – 9/16” Open End Box Wrench

Inspection of Valve and Hose Assembly

Quick Start Valve and Hose Assembly

•

Connect the valve and hose assembly to the FRL at
90-100 psi.

•

If air leaks around the housing plug, replace the o-ring
on the housing plug

•

If air leaks around the valve stem, replace the lower
valve stem o-ring.

•

If air leaks through the valve tube, replace the upper
valve stem o-ring.

•

If replacing the valve stem o-rings does not fix the air leak,
replace the valve body assembly

•

If the valve tube is dented, nicked, or scratched, replace the
valve body assembly.

•

If air can be felt leaving the muffler, replace the hose
assembly.

•

If the exhaust hose is cut, torn, or nicked, replace the
exhaust hose.

•

If the muffler is dirty or clogged, replace the muffler.

Housing Plug

Valve Stem

Muffler

Exhaust Hose

Valve Tube

Содержание Whizard Quantum Air 1000
























































































































































































Результаты поиска

Содержание Whizard Quantum Air 1000

Отзывы:

Похожие инструкции для Whizard Quantum Air 1000

Бренды по названию

Популярные бренды

BETTCHER INDUSTRIES Whizard Quantum Air 1000, Инструкция по эксплуатации и перечень запасных частей

Результаты поиска

Содержание Whizard Quantum Air 1000

Отзывы:

Похожие инструкции для Whizard Quantum Air 1000

Бренды по названию

Популярные бренды