BETTCHER INDUSTRIES Whizard Quantum Air 1000 Скачать руководство пользователя страница 64

Страница: 64 / 183

BETTCHER

Industries, Inc.

Maintenance

5-18

Maintenance
Whizard Quantum

Air Operating Instructions and Parts

List

Manual No. 102481
April 17, 2015

Power Unit / Head Assembly - Attachment and Adjustment

(Continued)

Step 6:

Install Drive Adapter

•

Insert the drive adapter and align the
square end with the square hole in the
power unit.

•

The drive adapter should drop in with
no force required.

•

The retaining ring will sit flush against
the attachment screw when properly
aligned.

Step 7:

Install Bearing

•

Slide the handpiece bearing into the
frame bore, aligning the bearing flat with
the frame flat.

•

The bearing should go in with minimal
effort and not require pressing.

•

Do not force the bearing into the frame.
If the bearing does not go in easily,
check frame and bearing for damage or
build-up.

Drive Adapter

Retaining Ring

Bearing

Bearing Flat

Frame Flat

Frame

Содержание Whizard Quantum Air 1000
























































































































































































Результаты поиска

Содержание Whizard Quantum Air 1000

Отзывы:

Похожие инструкции для Whizard Quantum Air 1000

Бренды по названию

Популярные бренды

BETTCHER INDUSTRIES Whizard Quantum Air 1000, Инструкция по эксплуатации и перечень запасных частей

Результаты поиска

Содержание Whizard Quantum Air 1000

Отзывы:

Похожие инструкции для Whizard Quantum Air 1000

Бренды по названию

Популярные бренды