BETTCHER INDUSTRIES Whizard Quantum Air 1000 Скачать руководство пользователя страница 80

Страница: 80 / 183

BETTCHER

Industries, Inc.

Maintenance

5-34

Maintenance
Whizard Quantum

Air Operating Instructions and Parts

List

Manual No. 102481
April 17, 2015

Power Unit

Power Unit Splines

Frame Splines for Power Unit

Greese Cup

Spacer Ring

Frame O-Rings (2)

Greese Ring

Assembly of Whizard Quantum

TRIMVAC

Handpiece

Prior to assembly, be certain all parts are clean and have been inspected for wear per Section 5.

Step 1: Attach Frame to Power
Unit:

Grease Cup and Ring

•

Pick up the Whizard

Trimmer.

•

Pick up the grease cup and ring.
Apply a small amount of
Whizard

Special Grease to the

frame o-rings.

•

With a twisting motion, install the
grease ring onto the frame over
the o-rings.

Be careful not to squeeze the o-rings out of their
grooves, or they could be trapped and damaged.

•

Rotate the grease cup to the desired position.

•

Slide the spacer ring onto the frame, small end first.

•

While holding the trimmer, pick up the power unit.

•

Firmly push the power unit towards the bottom of the spacer ring. Align the power unit
spline with the splines on the frame.

NOTE

The handle can be adjusted to suit the operator and the work station by pulling the

power unit back away from the frame and re-locating it on another set of notches on the
frame.

Содержание Whizard Quantum Air 1000
























































































































































































Результаты поиска

Содержание Whizard Quantum Air 1000

Отзывы:

Похожие инструкции для Whizard Quantum Air 1000

Бренды по названию

Популярные бренды

BETTCHER INDUSTRIES Whizard Quantum Air 1000, Инструкция по эксплуатации и перечень запасных частей

Результаты поиска

Содержание Whizard Quantum Air 1000

Отзывы:

Похожие инструкции для Whizard Quantum Air 1000

Бренды по названию

Популярные бренды