BETTCHER INDUSTRIES Whizard Quantum Air 1000 Скачать руководство пользователя страница 62

Страница: 62 / 183

BETTCHER

Industries, Inc.

Maintenance

5-16

Maintenance
Whizard Quantum

Air Operating Instructions and Parts

List

Manual No. 102481
April 17, 2015

Power Unit / Head Assembly - Attachment and Adjustment

(Continued)

Step 3:

Optional Thumb Support

•

Pick up a spacer ring or optional thumb
support.

•

If the optional thumb support is used, align
the thumb support splines with the frame
splines.

•

The optional thumb support should be located
on the opposite side of the grease cup.

Thumb Support Angle Adjustment

•

Lift up on the front of the thumb support
until the lug comes out of the notch underneath the thumb
support.

•

Rotate the thumb rest to a new position.

•

Push the thumb rest back down to seat the lug into a new

notch.

NOTE:

It may be necessary to rotate the grease cup to a new

position to adjust the thumb support to the desired position.

Optional Thumb Support

Thumb Support Splines

Fame Splines for
Thumb Support

Lift up

Lug

Adjustment
Notches

Thumb Rest

Содержание Whizard Quantum Air 1000
























































































































































































Результаты поиска

Содержание Whizard Quantum Air 1000

Отзывы:

Похожие инструкции для Whizard Quantum Air 1000

Бренды по названию

Популярные бренды

BETTCHER INDUSTRIES Whizard Quantum Air 1000, Инструкция по эксплуатации и перечень запасных частей

Результаты поиска

Содержание Whizard Quantum Air 1000

Отзывы:

Похожие инструкции для Whizard Quantum Air 1000

Бренды по названию

Популярные бренды