Bentel J408, Руководство по установке

Страница: 60 / 64

TERM. DESCRIPTION v(V) i(A)
2 and 4 ZONE MAIN BOARDS
[DL]
Supervised—Bypassable DIALLER Output :
during Standby è floating
on expiry of the Alarm Signalling Delay è negative pull-down to 0 V 0 0.1
[OC]
PROGRAMMABLE AUXILIARY Output :
during Standby è terminal floating
on verification of an associated event è negative pull-down to 0 V 0 1
[24V]
[ M ]
24 V POWER Output :
Positive pull-up to 27.6 V on [24V] terminal
Negative pull-down to 0 V on [ M ] terminal
27.6
0
1(4)
—
[24R]
[ M ]
RESETTABLE 24 V POWER Output :
during Standby è positive pull-up to 27.6 V on [24R] terminal
during Reset è [24R] terminal floating;
Negative pull down to 0 V on [ M ] terminal
27.6
—
0
1(4)
—
—
[PL]
POWER LOSS Output :
during Standby è floating
during power failure è negative pull-down to 0 V
—
0
—
1
ALARM
Non-Supervised—Silenceable ALARM Output :
Control panel in Standby è [COM] terminal connects to [NC] and [NO] floats
Control panel in Alarm è the [COM] and [NO] terminals connect, in accordance with programming — 5
FAULT
Non-Supervised—Silenceable—Bypassable FAULT Output :
Control panel in Standby è [COM] terminal connects to [NC] and [NO] floats
in the event of Fault è [COM] terminal connects to NO] and [NC] floats — 5
NAC1
Supervised—Silenceable—Bypassable ALARM Output N. 1:
Panel in Standby è negative pull-down to 0 V on [+] terminal; positive pull-up to 27.6 on [–] terminal
Panel in Alarm è positive pull-up to 27.6 on [+] terminal; negative pull-down to 0 V on [–] terminal 27.6 1(4)
NAC2
Supervised—Silenceable—Bypassable ALARM Output N. 2:
Panel in Standby è negative pull-down to 0 V on [+] terminal; positive pull-up to 27.6 V on [–] terminal
Panel in Alarm è positive pull-up to 27.6 on [+] terminal; negative pull down to 0 V on [–] terminal 27.6 1(4)
8 ZONE MAIN BOARD
RS485
RS485 Serial Port:
Positive pull-up to 27.6 V on [24V] terminal;
Negative pull-down to 0 V on [ M ] terminal;
data on [+] and [–] terminals
27.6
0
—
1(4)
—
—
EXTINGUISHMENT BOARD
EM
Supervised—Bypassable MANUAL EXTINGUISHMENT Input :
3.900 ohm (680 ohm se NC) across [+] and [–] terminals è Input in Standby
680 ohm (3.900 ohm se NC) across [+] and [–] terminals è PRE-EXTINGUISHMENT time
[+] and [–] terminals shorted or open è Manual Extinguishment Fault signalling
— —
IE
Supervised INHIBIT EXTINGUISHMENT Input:
3.900 ohm (680 ohm if NC) across [+] and [–] è Input in Standby
680 ohm (3.900 ohm if NC) across [+] an [–] terminals è EXTINGUISHMENT impossible
[+] and [–] terminals shorted or open è Inhibit Exting. Fault signalling
— —
PS
Supervised PRESSURE SWITCH Input:
3.900 ohm (680 ohm if NC) across [+] and [–] terminals è Input in Standby
680 ohm (3.900 ohm if NC) across [+] and [–] terminals è Pressure Switch Activated signalling
[+] and [–] terminals shorted or open è Pressure Switch Fault signalling
— —
[EV]
Supervised ELECTROVALVE Output:
Extinguishment Module in Standby è terminals disconnected
Extinguishment Module in Extinguishment phase è terminals connected
terminals shorted or open è Electrovalve Fault signalling
— 5
24P
POWER BOOST Input:
Power supply Input for the PR and AE Outputs — —
PR
Supervised PRE-EXTINGUISHMENT Output:
Extinguishment Module in Stand by è negative on [+] terminal, positive on [–] terminal
during the Pre-Extinguishment phase è positive on [+] terminal, negative on [–] terminal
terminals [+] and [–] shorted or open è Fault Pre Ext. signalling
-27.6
27.6
—
1
AE
ACTIVATED EXTINGUISHMENT Output:
Extinguishment Module in Stand by è negative on [+] terminal, positive on [–] terminal
during the Extinguishment phase è positive on [+] terminal, negative on [–] terminal
-27.6
27.6
—
1
Table 4 (...continued) Terminals Description