4.
Using the Jumper (
43
), marked “1” on the PCB, set
up the Extinguishment Module address:
Jumper (
43
) IN = Extinguishment Module nr. 1;
Jumper (
43
) OUT
=
Extinguishment Module nr. 2.
+
The Jumper (
59
), marked “2” on the PCB, MUST
BE INSERTED.
5.
Using the Flat cables connect the Extinguishment
Modules as follows:
6. if you are installing ONE Extinguishment Module
— connect it to the Main Board, via the jacks (
58
and
63
respectively), as per Fig. 9a;
if you are installing TWO Extinguishment Modules
—
connect Extinguishment Module nr. 1 to Extin-
guishment Module nr. 2, via the jacks (
56
) then,
connect Extinguishment Module nr. 1 to the Main
Board, via the jacks (
58
and
63
respectively), as per
Fig. 9b.
+
The polarity of the Flat cable connectors must be
observed.
n
Installing Expander Module Kit (for J424 ONLY)
This Expander Module Kit comprises an 8 zone Expan-
der Module and the Expander Control board. The
Expander Module contains most of the electronic circu-
itry and electrical terminals whereas the Expander Con-
trol board provides the LEDs and control keys for
Expander Module zones.
Install Expander Modules as follows:
Ø
if you are installing ONE Expander Module Kit
,
mount the Expander Module (
21
) and the Expander
Control board (
10
), as per Figure 11a;
Ø
if you are installing TWO Expander Module Kits
,
mount Expander Module nr. 1 (
21
) and the Expander
Control board (
10
) to the backplate then mount
Expander Module nr. 2 (
25
) and the Expander Con-
trol board (
7
), as per Figure 11b.
+
If you are installing ONE Expander Module Kit only,
the location will be different to that shown in the
diagram.
22
Conventional Fire Panels
J424/J408
13
9
28
31
13
9
28
a)
b)
27 63
58
27 63
56
29
56
Figure 9
Connecting ONE Extinguishment Module (
a
)
or TWO Extinguishment Modules (
b
) to a
J424
Control
panel:
9)
Main Control Board;
13)
Main Board;
27)
and
29
) Flat cable for the connection of the Extinguishment
Modules;
28)
Extinguishment Module nr. 1;
31)
Extin-
guishment Module nr. 2;
56)
Jack for the connection to
the consecutive Extinguishment Module;
58)
Jack for
the connection to the Main Board;
63)
Jack for the con-
nection of Extinguishment Module nr. 1.
93
93
95 96
97
98 99 98 99
100
100
93
98 99 98 99
100
100
a)
b)
c)
d)
e)
94
94
94
Figure 10
Installing an Expander Module Kit:
93)
Reverse locking supports;
94)
Expander Module anchor holes;
95)
Long plastic spacer;
96)
Expander Module placement screw;
97)
Expander Module nut;
98)
Expander Control Bo-
ard screws;
99)
Short plastic spacer;
100)
Expander Control Board nut.
Содержание J408
