USER MANUAL
KYO100-KYO300
11
The display will show the relevant details for each
Event. For example, Tamper Events show the TYPE
and TIME only.
To print Events from a specific Date
Using
C
or
D
scroll for the following message:
%$
&'(()
1!,
*!"
--
Press the
E
key, the display will show the Date prompt.
+,!, *!"--
.
Enter
all
the digits of the required Date (DD/MM/YYYY),
then press the
E
key.
The Keypad will exit the USER MENU, and the Printer
will print the Events starting from the entered date to the
most recent.
This facility is provided by the optional K3-PRT Printer
Interface (ask your Installer for details).
The Event Logger
The Event logger is set up as follows:
the Event number (
Ev.
) is shown on the left side of the
first line;
the Event details (
TYPE
,
IDENT.
,
USER
,
USER ID
,
TIME
) are shown on the second line.
Using the Event Logger:
Use
C
and
D
to scroll the Events.
Press
B
to view the Event details (see above).
Press the e to step back to the
Event Logger
menu.
The display will show the relevant details for each
Event. For example, Tamper Events show the TYPE
and TIME only.
Enable/Disable Auto-arm
Your Installer may have set up Partitions to turn ON/
OFF at preset times. This command will allow you to
turn the
Scheduler
ON/OFF, and Enable/Disable auto-
matic ON/OFF control.
Use
C
and
D
to scroll the Partitions, and the
O
and
o
keys to Enable/Disable the Scheduler.
!,,
02/3!'44
Press the
e
key to step back to the User menu.
Teleservice request
If your Installer has set up this facility, this command will
allow you to request on-line assistance (maintenance
that does not require components or wiring). Teleservice
requests will be confirmed by the following message:
#)5$#
/6
The Teleservice request will stop any ongoing Telephone
calls (Teleservice requests from the User have priority
over other call types), and will send the Teleservice call
(or calls) to the Installer telephone number (or numbers).
The installer must be equipped and ready for Tel-
eservice, otherwise the request will be ignored.
Enable/Disable Teleservice
This command will allow you to Enable/Disable the Con-
trol panel to receive Teleservice calls. The command will
be confirmed by the following message:
- +-+!-
+!-'44
Press
O
to
allow
the Control panel to receive Tel-
eservice calls.
Press
o
to prevent
the Control panel from receiving
Teleservice calls.
Press the
E
key to confirm and step back to the User
menu.
If Teleservice is disabled (OFF), the Control panel will
not accept incoming Teleservice calls, and on-line installer
assistance will not be possible.
If Teleservice is enabled (ON), the Installer will be able
to:
View the Control panel status
— Partition status;
Alarm memory, Bypassed zones, Zone status, Event
logger, Peripheral device status, etc.
Change the Control panel status
— Change Parti-
tion status, Clear the Alarm memory and Bypass zones
(active User Code required).
Change the Control panel parameters
— if all the
partitions are disarmed and the Partition Patrol Times
are not active.
The Teleservice facility allows the Installer to check and
work on the Control panel from a remote computer, and
carry out maintenance work that does not require new
wiring or components.
An
*
will be shown on the display directly above the
t
when the Teleservice facility is enabled.
Enable/disable Answering device
This command will allow you to turn ON/OFF the An-
swering device. If the Answering device is ON, the Con-
trol panel will answer incoming calls with a Voice mes-
sage. This facility is provided by the
K3-VOX
Voice board
(accessory item).
Содержание KYO 100
Страница 1: ......
