BendPak LR-10000 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 44

background image

LR-10000 Low-Rise Scissor Lift

26

P/N 5900075 — Rev. A1 — April 2019

To connect to a Power Source and add Hydraulic Fluid

:

1.

Have the Electrician locate the Pigtail coming out of the Electrical Box on the Power Unit.

2.

Open the Electrical Box, remove the Pigtail, and then wire a Power Cord (with an appropriate Plug)

inside the Electrical Box

to the wiring that was connected to the Pigtail.

The Electrician needs to provide the Power Cord and Plug; these are

not

supplied with the Lift.

Refer to

Wiring Diagram

for wiring information.

⚠

DANGER

All wiring

must

be performed by a licensed, certified Electrician. Do not perform

any

maintenance or installation on the lift without first making sure that main

electrical power has been disconnected from the lift and

cannot

be re-energized

until all procedures are complete.

Important electrical information:

•

Improper elec

trical installation can damage the Power Unit motor; this damage is not covered by

the warranty.

•

If you have multiple Power Units, use a separate circuit breaker for each Power Unit.

•

Protect each circuit with a time-del

ay fuse or circuit breaker. For a 115 VAC, 1 phase circuit, use

a 15 amp or greater fuse. For a 230 VAC, 1 phase circuit, use a 25 amp or greater fuse.

3.

Fill the Hydraulic Fluid reservoir.
The Power Unit’s Hydraulic Fluid reservoir must be filled with Hydraulic Fluid or automatic
transmission fluid

before

you begin operation. When you receive it, the reservoir is empty; the

Power Unit will not work correctly until it is filled with approved fluids.
Approved Hydraulic Fluids are any general purpose ISO-32, ISO-46, or ISO-68 hydraulic oil or

approved automatic transmission fluids such as Dexron III, Dexron VI, Mercon V, Mercon LV, Shell
Tellus S4 / S3 / S2, or any synthetic multi-Vehicle automatic transmission fluid.

⚠

WARNING

Do not run your Power Unit without Hydraulic Fluid; you will damage it.

Install a Power Disconnect Switch

⚠

WARNING

A Power Disconnect Switch is

not

provided with this equipment.

A Power Disconnect Switch is a National Electrical Code (NEC) requirement. They are designed to

interrupt main electrical power in the event of an electrical circuit fault, emergency situation, or when

equipment is undergoing service or maintenance.
Make sure to install a Power Disconnect Switch that is properly rated for the incoming power source.
Your Power Disconnect Switch must be installed so that it is in

easy reach of the Operator

or in

their line of sight. The Power Disconnect Switch must be

clearly marked

to indicate its purpose.

If you are not clear where to put the Power Disconnect Switch, consult with your Electrician.

⚠

DANGER

Installing a Thermal Disconnect Switch

must

be performed by a licensed, certified

Electrician.

Have your Electrician select a

UL-listed

Power Disconnect Switch.

«
...
24
25
26
27
28
...
»

Содержание LR-10000













































Отзывы:

Нет отзывов

Похожие инструкции для LR-10000

Бренд: IBM Страницы: 72

Бренд: Wayne-Dalton Страницы: 24

Бренд: Fagor Страницы: 103

Бренд: Magmaweld Страницы: 172

Бренд: S7 Страницы: 14

Бренд: S.R.Smith Страницы: 2

Бренд: Handicare Страницы: 20

Бренд: Clarke Страницы: 8

Бренд: Skov Страницы: 68

Бренд: Migatronic Страницы: 28

Бренд: Hall Research Technologies Страницы: 47

Бренд: GYS Страницы: 24

Бренд: Urrea Страницы: 16

Бренд: ESAB Страницы: 46

Бренд: GRS Страницы: 4

Бренд: Firepower Страницы: 52

Бренд: M-system Страницы: 6

Бренд: Migatronic Страницы: 106

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды