BendPak LR-10000 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 44

background image

LR-10000 Low-Rise Scissor Lift

22

P/N 5900075 — Rev. A1 — April 2019

Connect the Hydraulic Lines

Hydraulic Lines provide Hydraulic Fluid to the Hydraulic Cylinders, where it is used to raise the

Platforms.
The LR-10000 comes with one Long Hydraulic Line (black rubber) and one Short Hydraulic Line (silver

metal). The Long Hydraulic Line goes from the Power Unit to the closest Hydraulic Cylinder. The Short

Hydraulic Line goes from the first Hydraulic Cylinder to the other Hydraulic Cylinder.

The Short Hydraulic Line, and the two Hydraulic Fittings that go on either end of it,

come installed from the factory.

Note

: The drawings and instructions in this section assume the Power Unit Stand was installed on

the left side of the Lift (looking at it from the Short Ramp end). If you installed it on the right
side of the Lift, modify the instructions accordingly.

The following drawing is an overview of how the Hydraulic Lines are routed to the Hydraulic Cylinders.

Drawing not necessarily to scale. Some components not shown, other components exaggerated for

clarity. Power Unit shown on the left of the Lift (looking at the Short Ramp end).

To connect the Hydraulic Lines

:

1.

Locate the Long Hydraulic Line and the Elbow Hydraulic Fitting.

2.

Starting at the Power Unit, remove the Shipping Plug from one of the two Hydraulic Power Out

connectors on the Power Unit. It does not matter which one you use. They are labeled P1 and P2.
The Hydraulic Power Out connectors are shown in the drawing in

Preparing the Power Unit

3.

Attach the Elbow Hydraulic Fitting (06 ORB – 04 JIC) to the Hydraulic Power Out connector whose
Shipping Plug you removed.

«
...
20
21
22
23
24
...
»

Содержание LR-10000













































Отзывы:

Нет отзывов

Похожие инструкции для LR-10000

Бренд: Handicare Страницы: 56

Бренд: Eastwood Страницы: 16

Бренд: Eastwood Страницы: 16

Бренд: Feig Electronic Страницы: 153

Бренд: Jacka Industries Страницы: 24

Бренд: H3C Страницы: 8

Бренд: heat-timer Страницы: 36

Metalmaster 200d Pro DC GTAW

Бренд: Tokentools Страницы: 33

Бренд: Nibe Страницы: 16

NuDAQ cPCI-7248

Бренд: ADLINK Technology Страницы: 59

TE-6201-W Series

Бренд: Pro's Kit Страницы: 2

Бренд: M-system Страницы: 10

Бренд: M-system Страницы: 10

Бренд: M-system Страницы: 5

Бренд: Triax Страницы: 52

Бренд: Bame Страницы: 12

iNELS Air AirIM-100S

Бренд: Elko Страницы: 8

Бренд: WAGO Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды