BendPak LR-10000 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 44

background image

LR-10000 Low-Rise Scissor Lift

25

P/N 5900075 — Rev. A1 — April 2019

Preparing the Power Unit

The Power Unit comes fully assembled from the factory. You need to attach it to the Power Unit Stand

(already done, as described in

Attach the Power Unit

), connect it to a power source, and fill the

Hydraulic Fluid Reservoir with Hydraulic Fluid.
The Power Unit for the LR-10000 is 208–240 VAC, 50/60 Hz, 1 phase. The Hydraulic Fluid Reservoir

holds about 5.65 liters (1.5 gallons) of Hydraulic Fluid.
The Lift uses electrical energy; if your organization has Lockout/Tagout policies, make sure to

implement them once the unit is connected to a power source.

⚠

DANGER

All wiring

must

be performed by a licensed, certified Electrician.

Refer to

Wiring Diagram

for wiring information.

⚠

CAUTION

The Power Unit’s motor is

not

thermally protected.

The Power Unit has multiple connections:
•

Hydraulic Line

. The Hydraulic Line should already be connected to the Power Unit. If it is not,

refer to

Connect the Hydraulic Lines

for more information.

•

Power Source

. The Power Unit has to connect to an appropriate power source. A licensed,

certified Electrician is

required

to make this connection. The Electrician needs to provide an

appropriate Power Cord and Plug; these are

not

supplied with the Lift.

The following drawing shows the Power Unit of the LR-10000.

Drawing is not necessarily to scale. Your Power Unit may be different from what is shown here.

«
...
23
24
25
26
27
...
»

Содержание LR-10000













































Отзывы:

Нет отзывов

Похожие инструкции для LR-10000

PROFINET BNI PNT-508-055-P067

Бренд: Balluff Страницы: 84

Бренд: Linak Страницы: 33

Бренд: Walter Страницы: 132

Бренд: heat-timer Страницы: 40

Бренд: JLG Страницы: 97

Бренд: Danfoss Страницы: 36

Бренд: Revo Страницы: 6

Бренд: Miller Electric Страницы: 32

PRO POWER VIAS200

Бренд: VITO Страницы: 16

Бренд: Peak Страницы: 41

MIG PULSER 10213

Бренд: Lincoln Electric Страницы: 22

InvertaPuls IP4-3

Бренд: WIELANDER+SCHILL Страницы: 31

Бренд: stertil-KONI Страницы: 50

Бренд: Omron Страницы: 297

Бренд: Strata Страницы: 36

ALIGNMENT EELR124A

Бренд: Sun Microsystems Страницы: 42

Бренд: Johnson Controls Страницы: 13

Бренд: ESAB Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды