BendPak LR-10000 Скачать руководство пользователя страница 7

Страница: 7 / 44

LR-10000 Low-Rise Scissor Lift

P/N 5900075 — Rev. A1 — April 2019

Frequently Asked Questions

Question

: How much weight can the LR-10000 raise?

Answer

: The LR-10000 can raise Vehicles up to 10,000 pounds (4,536 kg).

: Can the LR-10000 be installed outside?

: No. The LR-10000 is approved for indoor installation and use only.

Outdoor installation is

prohibited

: Can I put the Power Unit Stand on either side of the LR-10000?

: Yes. The Power Unit Stand can be located on either side of the Lift. The drawing on the previous

page shows the Power Unit Stand on the left if you are looking at the Short Ramp end of the Lift.
Note that the Safety Lock Release Handle

cannot

be moved to the other side. It can only be

installed and used on the left side of the Lift if you are looking at the Short Ramp end.

: How far can the Power Unit Stand be from the closest side of the Lift?

: If you want the Power Unit Stand on the left side of the Lift (looking at it from the Short Ramp end),

it can be installed up to 77 inches / 1,956 mm from the side of the Lift. If you want the Power Unit

on the right side of the Lift, it can be installed up to 53 inches / 1,346 mm from the side of the Lift.

: What if I want to raise a Vehicle that is slightly over the weight capacity of the Lift?

: This is not an intended use of the product. We strongly recommend against trying to raise a

Vehicle that is heavier than the rated capacity.

: How many locking positions does my Lift have?

: Three. This gives you multiple heights to which you can raise the Lift, so it is easy to find the right

height for the work you are doing.

: What do the Safety Locks do?

: Safety Locks use gravity to hold the Platforms up, once they are

engaged

. Even if the Lift loses

power, the Platforms stay where they are if they were left

engaged

on a Safety Lock.

Only leave

your Lift either fully lowered or engaged on a Safety Lock!

: Which end of the LR-10000 is the “front”?

: Neither. You can drive onto the Lift from either direction; there are ramps on both ends.

: The LR-10000 is described as “frame-engaging”, what does that mean?

: it means the Platforms (actually, the Lift Pad or Lift Extensions on the Platforms) contact the

underside of the Vehicle to raise it, leaving the wheels free. Put another way, the Vehicle is

not

raised on its wheels, like a Vehicle on a four-post Lift.

: Anything else I should be aware of?

: One thing. Do not remove all four of a Vehicle’s tires while it is on the LR-10000 and then lower the

Vehicle all the way to the ground. It will go down, but it will have a hard time coming back up

again. The Lift requires some space to build up enough upward force to raise a Vehicle.

Содержание LR-10000












































Результаты поиска

Содержание LR-10000

Отзывы:

Похожие инструкции для LR-10000

Бренды по названию

Популярные бренды

BendPak LR-10000, Инструкция по установке и эксплуатации

Результаты поиска

Содержание LR-10000

Отзывы:

Похожие инструкции для LR-10000

Бренды по названию

Популярные бренды