BendPak LR-10000 Скачать руководство пользователя страница 35

Страница: 35 / 44

LR-10000 Low-Rise Scissor Lift

P/N 5900075 — Rev. A1 — April 2019

Troubleshooting

This section describes how to troubleshoot your Lift.

Note

: If your Lift is not functioning correctly, you must take it out of service until it is fixed.

Important

: All repair work

must

be done by qualified personnel.

Issue

Action to Take

Platforms move erratically
or squeak when in use.

Move the Platforms up and down a few times, with a break between
each; there could be residual air in the Hydraulic System.

Platforms do not go up or

down.

Make sure the Power Unit is connected to an appropriate power

source.
Make sure the Hydraulic Lines are not pinched or leaking.
Make sure there is sufficient Hydraulic Fluid in the reservoir on the

Power Unit.

Vehicle with no tires is fully

lowered, Lift will not go up.

Too much weight on the Frames; no room to get upward motion

started. Refer to

Vehicle with No Tires Fully Lowered

Hydraulic Fluid is old or

dirty.

Replace the dirty fluid with clean, approved Hydraulic Fluids, such as

Dexron III, Dexron VI, Mercon V, Mercon LV, Shell Tellus S4 / S3 /

S2, or comparable.

Platforms make odd noises

when in use.

Lubricate hinge points using white lithium grease.

Platforms are slowly

lowering on their own.

Make sure both Platforms are engaged on Safety Locks (if not,

Hydraulic Fluid could be leaking out, lowering the Platforms). Only
leave the Lift either fully lowered or engaged on a Safety Lock.

If you continue to have problems with your Lift, contact your dealer, visit

bendpak.com/support

[email protected]

, or call

(800) 253-2363

, extension 196.

Vehicle with No Tires Fully Lowered

The issue is that there is too much weight on the LR-10000 Frames with no room to get upward force
started. You need to reduce the weight by at least half or raise the Vehicle off the Frames some other

way.
Methods that have fixed this issue include:
•

Use a floor jack to raise the Vehicle from four to six inches, giving enough room to get upward
force started

•

Use lifting equipment to raise the Vehicle off the Frames

If you are still unable to raise your Vehicle, contact Technical Support for assistance.

Содержание LR-10000












































Результаты поиска

Содержание LR-10000

Отзывы:

Похожие инструкции для LR-10000

Бренды по названию

Популярные бренды

BendPak LR-10000, Инструкция по установке и эксплуатации

Результаты поиска

Содержание LR-10000

Отзывы:

Похожие инструкции для LR-10000

Бренды по названию

Популярные бренды