BendPak Clearfloor 10AP Скачать руководство пользователя страница 72

Страница: 72 / 96

10AP Series Two-Post Lifts

P/N 5900265 — Rev. A6 — December 2022

Broken Safety Cable Procedure

If the Safety Cable breaks, the Powerside Lift head will lower but the Offside Lift Head will not.

To release the Offside Safety Lock:

1. Raise the Lift Heads off the Safety Locks.
2. Have an assistant reach through the access hole with a stiff wire or pick to pull the Safety Block

away from the Lift Head. See figure below.

3. Hold in the Safety Release on the Powerside Lift Post while holding the lower handle on the Power

Unit.

4. When the Lift heads are on the ground and the Lift is in a safe condition, remove power from the

Lift and replace the Safety Cable.

Reference only – do not scale.

Содержание Clearfloor 10AP
































































































Результаты поиска

Содержание Clearfloor 10AP

Отзывы:

Похожие инструкции для Clearfloor 10AP

Бренды по названию

Популярные бренды

BendPak Clearfloor 10AP, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Clearfloor 10AP

Отзывы:

Похожие инструкции для Clearfloor 10AP

Бренды по названию

Популярные бренды