BendPak Clearfloor 10AP Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 96

background image

10AP Series Two-Post Lifts

27

P/N 5900265 — Rev. A6 — December 2022

The opening in the Post Extension faces the inside of the Lift.
Secure the Post Extension to the Lift Post, using the hardware listed in the illustration above.
Slide on the other Post Extension to the other Lift Post and secure it the same way.

Hydraulic System Warnings:

⚠

DANGER

Failure to observe these warnings can result in serious personal injury including, in
rare cases, death.

⚠

WARNING

The Hydraulic Hoses and connections

must

be inspected before any attempt to

raise a Vehicle is made.

⚠

WARNING

Double check to

verify

all Hydraulic Hose connections and fittings, including

unused auxiliary port plugs on the Power Unit, the Flow Divider, the Cylinders and
anywhere else in the Hydraulic System are tightened.

⚠

WARNING

The Power Unit is a Hydraulic Pump capable of developing pressures in excess of
5,000 psi (345 BAR). A pressure relief valve is used to set the pressure at the

desired level. Tampering with, adjusting, modifying, or removing the relief valve is
extremely dangerous and is not recommended. Only trained Hydraulics Technicians

should adjust the relief valve, using calibrated Hydraulic Pressure gauges to assure

the proper pressure setting is achieved.

⚠

WARNING

Changes to the output pressure may render the power unit incompatible with
pressure limitations of other components in the Hydraulic Circuit. This may cause

catastrophic failure of those components, and could result in property damage,

serious personal injury, or death.

⚠

DANGER

The Hydraulic System can contain high pressure which, if suddenly released, can
cause serious injury or death.

⚠

WARNING

Do

not

attempt to connect or disconnect Hydraulic Hoses while the equipment is

loaded, or while a Vehicle is on the Lift, or the Hydraulic System is under pressure.

⚠

WARNING

Keep bare hands away from Hydraulic Fluid; always wear gloves when handling
Hydraulic Fluid, Cylinders or Hydraulic Hoses.

⚠

WARNING

When handling Hydraulic Fluid, always observe the safety instructions from the
manufacturer.

⚠

WARNING

Always

promptly clean any Hydraulic Fluid spills. If a leak is the source of the spill,

lockout the Lift to prevent use until the Hydraulic System is repaired.

«
...
25
26
27
28
29
...
»

Содержание Clearfloor 10AP

































































































Отзывы:

Нет отзывов

Похожие инструкции для Clearfloor 10AP

Бренд: Sabaj Страницы: 12

Бренд: Campbell Страницы: 72

Бренд: S7 Страницы: 14

Бренд: S.R.Smith Страницы: 2

Бренд: Laars Страницы: 9

BLUEBOX ADVANT UHF

Бренд: iDTRONIC Страницы: 54

Бренд: B&B Molders Страницы: 18

Бренд: Hall Research Technologies Страницы: 47

Бренд: OEM Tools Страницы: 8

Бренд: Nußbaum Hebetechnik Страницы: 32

Бренд: WAGO Страницы: 12

Бренд: Velux Страницы: 24

ISaGRAF VP-2117

Бренд: ICP DAS USA Страницы: 75

Бренд: M-system Страницы: 7

Бренд: Telwin Страницы: 56

Бренд: HEIDENHAIN Страницы: 98

Бренд: Fenix Страницы: 24

Бренд: STAMOS Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды