BendPak Clearfloor 10AP Скачать руководство пользователя страница 14

Страница: 14 / 96

10AP Series Two-Post Lifts

P/N 5900265 — Rev. A6 — December 2022

Reviewing the Installation Orientation

Keep these factors in mind when deciding how to orient the Lift:
• The first thing to figure out is which direction you will be driving the Vehicles in, called

the

Approach

In most cases, this is simple: there’s a driveway on one side and a wall on the other side.

The driveway is your Approach. This makes the wall side the Front of the Lift and the
driveway side the Rear of the Lift.

If both sides are open, decide which way you will be driving Vehicles onto the Lift. This is

the Approach; the drive-

side is the Rear of the Lift and the drive-

off

side if the Front.

•

The Power Unit must be installed on the Powerside Post

. You can identify the

Powerside Post by the Mounting Bracket to which the Power Unit attaches; only one Post that

came with your Lift has a Mounting Bracket.
The following illustration shows the Power Unit location for your Lift.

Reference only – do not scale.

Top View

Содержание Clearfloor 10AP
































































































Результаты поиска

Содержание Clearfloor 10AP

Отзывы:

Похожие инструкции для Clearfloor 10AP

Бренды по названию

Популярные бренды

BendPak Clearfloor 10AP, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Clearfloor 10AP

Отзывы:

Похожие инструкции для Clearfloor 10AP

Бренды по названию

Популярные бренды