BendPak Clearfloor 10AP Скачать руководство пользователя страница 41

Страница: 41 / 96

10AP Series Two-Post Lifts

P/N 5900265 — Rev. A6 — December 2022

Reference only – do not scale.

Perform Steps 3 through 9 for the other Equalizing Cable.

Mounting the Power Unit

This section describes how to mount the Power Unit to the Powerside Post. You do

not

need an

Electrician to

mount

the Power Unit, but you do need an Electrician to

connect

the Power Unit.

Refer to

Connecting the Power Unit

for installation information for your Electrician and specific

information about the Power Unit that came with your Lift.

NOTICE

Do not connect the Power Unit to the Hydraulic System or to the power source at
this point in the installation; those connections will be made later.

⚠

CAUTION

The Power Unit is heavy. BendPak recommends having one person hold the Power
Unit while a second person bolts it into place.

To mount the Power Unit

Find the supplied four Hex Head Bolts, four Nyloc Nuts, and one Vibration Dampener.
Remove the Power Unit from the packaging material.

Important

The Power Unit is heavy. BendPak recommends having one person hold the Power Unit
while a second person bolts it into place.

Put the Vibration Dampener into place next to the Mounting Bracket on the Powerside Post.
Move the Power Unit Mount Plate next to the Vibration Dampener.
Secure the Power Unit and Vibration Dampener using the hardware listed below, using all four

holes to secure the Power Unit.

Содержание Clearfloor 10AP
































































































Результаты поиска

Содержание Clearfloor 10AP

Отзывы:

Похожие инструкции для Clearfloor 10AP

Бренды по названию

Популярные бренды

BendPak Clearfloor 10AP, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Clearfloor 10AP

Отзывы:

Похожие инструкции для Clearfloor 10AP

Бренды по названию

Популярные бренды