BendPak Clearfloor 10AP Скачать руководство пользователя страница 51

Страница: 51 / 96

10AP Series Two-Post Lifts

P/N 5900265 — Rev. A6 — December 2022

Contact the Electrician

As mentioned previously, there are installation tasks that require a certified Electrician.

⚠

DANGER

All wiring

must

be performed by a licensed, certified Electrician in accordance with

all applicable local electrical codes.

The Electrician needs to:
•

Connect to power

. The Power Unit comes with a pigtail for wiring to a power source. Have your

Electrician connect a power cord with plug to the electrical box on the Lift (for connection to a

power outlet) or have them wire it directly into the electrical system at the Lift location.

•

Connect the Microswitch to the Power Unit

. The Microswitch (which is next to the Safety

Shutoff Bar) must be wired to the Power Unit. The necessary wiring is included.

•

Install a Power Disconnect Switch

. Ensures you can quickly and completely interrupt

electrical power to the Lift in the event of an electrical circuit fault, emergency, or when equipment

is undergoing service or maintenance. You must put it within sight and easy reach of the Lift

operator. Refer to

Installing a Power Disconnect Switch

for more information.

•

Install a Thermal Disconnect Switch

. Ensures the equipment shuts down in the event of an

overload or an overheated motor. Refer to

Installing a Thermal Disconnect Switch

for

more information.

These installation tasks are described in detail in the following sections.
The Electrician is responsible for providing:
•

A power cord and appropriate 220 VAC plug for connecting to an appropriate power source or the

items required to connect to the facility’s power system

•

a Power Disconnect Switch

•

a Thermal Disconnect Switch

Additional information is supplied in the following sections describing these tasks.

Electrical Information

⚠

DANGER

All wiring

must

be performed by a licensed, certified Electrician in accordance with

all applicable local electrical codes. Do not perform any maintenance until main

electrical power has been disconnected from the Lift and cannot be re-energized

until all procedures are complete.

Important electrical information:

•

Improper electrical installation can damage the Power Unit motor, which is not covered by the

warranty.

•

The Lift uses electrical energy; if your organization has Lockout/Tagout policies, make sure to
implement them after connecting to a power source.

•

Use a separate circuit breaker for each Power Unit.

•

Protect each circuit with a time delay fuse or circuit breaker:
–

For a 208 to 230 VAC,

single phase

circuit, use a 15-amp circuit breaker.

Содержание Clearfloor 10AP
































































































Результаты поиска

Содержание Clearfloor 10AP

Отзывы:

Похожие инструкции для Clearfloor 10AP

Бренды по названию

Популярные бренды

BendPak Clearfloor 10AP, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Clearfloor 10AP

Отзывы:

Похожие инструкции для Clearfloor 10AP

Бренды по названию

Популярные бренды