manualshive.com logo in svg

Belshaw Brothers Donut Robot Mark VI, Руководство оператора

Поделиться
Скачать
Belshaw Brothers Donut Robot Mark VI Скачать руководство пользователя страница 31

 

Belshaw Adamatic Bakery Group 

•

 www.belshaw-adamatic.com 

•

 206-322-5474 

•

[email protected] 

Donut Robot Mark VI Technical Supplement 

MN-1033EN 

13 

4 

Troubleshooting 

 

CAUTION 

If you perform repairs yourself or have 

them performed by anyone other than a 

service technician authorized by Belshaw 

Adamatic Bakery Group, you do so at your 

own risk. 

 
This section is designed as an aid in 

troubleshooting with the Donut Robot

 Mark VI 

and FT2-DW Feed Table. It is not a substitute for 

a qualified technician.  You may encounter a 

problem with your machine that is not covered in 

this section, or you may try the remedies 

suggested here and find that they do not solve the 

problem.  If this happens, call your dealer or 

another qualified technician.  Also, call your 

dealer if you need a replacement part. 
If you need assistance in identifying a part, you 

can contact Belshaw Adamatic Service Dept at 

800-578-2547 or email 

[email protected]

. 

You will need to state: 

•

 

The model name of the machine. 

•

 

The serial number of the machine. 

•

 

The voltage, phase, and cycle of the 

machine. 

Following is a troubleshooting chart to help 

identify and solve problems with the Mark VI.  

See also “Donut-Making Helps.” 

WARNING 

To avoid being burned, electrocuted, or 

otherwise injured, unplug the machine and 

allow it to cool before disassembling, 

repairing, or wiring. 

Содержание Donut Robot Mark VI


















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды