Belshaw Brothers Donut Robot Mark VI Скачать руководство пользователя страница 14

Страница: 14 / 49

Belshaw Adamatic Bakery Group

•

www.belshaw-adamatic.com

•

206-322-5474

•

[email protected]

MN-1032EN

Donut Robot

Mark VI Operator’s Manual

Maintenance

WARNING

To avoid being burned, electrocuted, or

otherwise injured, always unplug the

machine and allow it to cool down before

making adjustments, clearing obstructions,

lubricating, cleaning, or disassembling.

Taking Care of the Plunger,

Hopper, and Cylinder

These instructions apply to the Donut Robot cake

donut depositor (or Dual Automatic Depositor).

For instructions on maintaining a Type F cake

donut depositor, refer to the Type F manual.

The plunger, hopper, and cylinder of your Donut

Robot are precision instruments. With proper

care, they will perform well for years. Follow

these guidelines:

Clean these parts only in the manner

explained in this manual.

Handle these parts with care. Avoid

dropping them on hard surfaces.

Do not force the machine if it becomes

jammed. To avoid damaging the

plunger, disassemble the machine and

remove any obstructions.

Lubrication

Daily

Before using the machine each day, apply Food

Grade mineral oil to the plunger connecting rod.

The oil should penetrate the ball lock and the

spring socket. See Figure 6.

Figure 6 Lubricating the Connecting Rod.

Weekly

Apply a few drops of Food Grade mineral oil to

the swing column where it contacts the swing

column bracket.

Содержание Donut Robot Mark VI


















































Результаты поиска

Содержание Donut Robot Mark VI

Отзывы:

Бренды по названию

Популярные бренды

Belshaw Brothers Donut Robot Mark VI, Руководство оператора

Результаты поиска

Содержание Donut Robot Mark VI

Отзывы:

Бренды по названию

Популярные бренды