Belshaw Brothers Donut Robot Mark VI Скачать руководство пользователя страница 28

Страница: 28 / 49

Belshaw Adamatic Bakery Group

•

www.belshaw-adamatic.com

•

206-322-5474

•

[email protected]

MN-1033EN

Donut Robot Mark VI Technical Supplement

Leveling and Securing the

Fryer

Check to see if the fryer is level. If it is not,

adjust the heights of the legs. Be sure that all six

legs rest on the work surface when the fryer is

level.
Bolt the fryer to the work surface as follows:
1. There are brackets on the ends of the fryer

case. Each has a hole in it. Mark the

locations of the holes on the work surface.

2.  Drill holes through the work surface.
3.  Insert bolts through the holes.
4.  Tighten nuts onto the bolts to ensure that the

Donut Robot will not move.

Moving the Fryer

If you ever want to move the fryer to a different

workstation, follow this procedure:
1. Turn off the machine and disconnect it from

the power source. Unplug the depositor

power cord.

2. Allow the machine and the shortening to

cool.

WARNING

Do not touch hot shortening. It can cause

serious burns.

3. Remove and set aside the plunger, the

hopper, and the cutter head, in that order.

4. Disconnect the swing connecting rod.
5. Remove the shortening from the fryer as

explained in “Removing the Shortening” in

Section 3.

6. To avoid dropping the machine or getting

shortening on the floor wipe excess

shortening off of the fryer and the conveyor.

WARNING

Thoroughly clean and dry the floor if

shortening is spilled. Materials on the

floor can cause people to slip or fall,

resulting in serious injury or loss of life.

7. Set aside the conveyor.
8. Remove the clevis pins that hold the heater

head in place. Remove the heater head from

the fryer.

9. To prevent tripping, coil the power cord.

Move the heater head to the new

workstation.

10.  Move the fryer to its new location.
11.  Install the heater head.
12.  Move and install the conveyor.
13  Move and install the swing column.

Connect the swing connecting rod.

14. Move and install the depositor’s cutter head

(the motor and electrical compartment).

15. Move and install the hopper and the plunger.
16. Level and secure the fryer.

Содержание Donut Robot Mark VI


















































Результаты поиска

Содержание Donut Robot Mark VI

Отзывы:

Бренды по названию

Популярные бренды

Belshaw Brothers Donut Robot Mark VI, Руководство оператора

Результаты поиска

Содержание Donut Robot Mark VI

Отзывы:

Бренды по названию

Популярные бренды