Belshaw Brothers Donut Robot Mark VI Скачать руководство пользователя страница 30

Страница: 30 / 49

Belshaw Adamatic Bakery Group

•

www.belshaw-adamatic.com

•

206-322-5474

•

[email protected]

MN-1033EN

Donut Robot Mark VI Technical Supplement

Figure 2-3. Lubricating the Drive Gears.

Replace the back cover of the heater head.

Taking Care of the Plunger,

Hopper, and Cylinder

The plunger, hopper, and cylinder of your Donut

Robot are precision instruments. If you take

good care of them, they will perform well for

years. Follow these guidelines:

•

Clean these parts only in the manner

explained in this manual.

•

Handle these parts with care. Avoid

dropping them on hard surfaces.

•

Do not force the machine if it becomes

jammed. To avoid damaging the

plunger, disassemble the machine and

remove any obstructions.

FT2DW Feed Table

After Each Use

Use a soft, damp cloth for cleaning.

WARNING

To avoid electrocuting yourself or

damaging the machine, never allow any

liquid to enter the power head.

Adjust conveyor chain tension

If the tension of the conveyor chains needs

adjusting, follow these steps:
1. Loosen the hex head bolts that hold the

roller shaft at the outfeed end of the

conveyor.

2. Pull the shaft until the chains reach the

correct tension. The tension is correct when

you can lift the chains about 1”/2,5 cm

above the surface of the Feed Table. Each

chain should have the same tension.

3. Tighten the hex head bolts that hold the

roller shaft.

•

Содержание Donut Robot Mark VI


















































Результаты поиска

Содержание Donut Robot Mark VI

Отзывы:

Бренды по названию

Популярные бренды

Belshaw Brothers Donut Robot Mark VI, Руководство оператора

Результаты поиска

Содержание Donut Robot Mark VI

Отзывы:

Бренды по названию

Популярные бренды