Belden lumberg automation 934 878-001 Скачать руководство пользователя страница 48

Страница: 48 / 75

7.2 Voltage Errors at M12 Slots

(Sensor Short Circuit)

7 Diagnostic Properties of the

Modules

of the module. The value of this parameter can range from 0 to 255 ms; the

factory setting is 80 ms.
The filter is used to avoid premature error messages when a capacitive load is

activated or an inductive load is deactivated, and during other voltage peaks

when a status changes.
When a channel is in the static state – that is, when it is permanently activated

or deactivated – the controller uses a fixed specified duration of 100 ms for

filtering the error message.

7.2 Voltage Errors at M12 Slots (Sensor Short

Circuit)

On each M12 input connector of the modules, contact 1 provides a 24 V

potential for power supply. This potential is obtained from the system/sensor

voltage U

and monitored.

In the case of a sensor short-circuit, a voltage error is reported. Both channel

indicators of the M12 input socket light up red, and the relevant error bit for

the sensor short-circuit is set in the diagnosis bytes.
The error message is filtered by the "Surveillance Timeout" parameter. The

same parameters as for the channel errors are also used for the voltage

errors.

7.3 Overload of Output Drivers

The output drivers of the modules with output functions (variants 16DO,

8DI/8DO and 16DI/DO) report an error when they detect an overload. This

error is reported by setting the relevant channel error bits in the diagnosis

bytes.

Technical Manual LioN-P PROFINET

Version 2.0 10/2017

Содержание lumberg automation 934 878-001












































































Результаты поиска

Содержание lumberg automation 934 878-001

Отзывы:

Похожие инструкции для lumberg automation 934 878-001

Бренды по названию

Популярные бренды

Belden lumberg automation 934 878-001, Техническое руководство

Результаты поиска

Содержание lumberg automation 934 878-001

Отзывы:

Похожие инструкции для lumberg automation 934 878-001

Бренды по названию

Популярные бренды