Belden lumberg automation 934 878-001 Скачать руководство пользователя страница 50

Страница: 50 / 75

7.5 Error in System/Sensor Power

Supply

7 Diagnostic Properties of the

Modules

Attention:

Every output channel that is active at the same time as the

error occurs in supply voltage U

is locked. This means that for correct

operation, the output channel must be reset by the controller when the

status of the supply voltage U

has normalized again. We recommend

deactivating all output channels with the controller as soon as the

undervoltage is detected. Otherwise, because it is locked, every active

output channel will report a diagnosis when the voltage value has

normalized again.

The error message is filtered by means of a fixed filter period of 300 ms.

7.5 Error in System/Sensor Power Supply

The voltage value for the system/sensor power supply is also monitored

globally. If the value goes outside the voltage range of 18 to 30 V, an error

message is created.
The U

indicator lights up red and the sensor undervoltage bit is set in the

module information byte.
The error message has no effect on the outputs and is not filtered, but is

reported immediately.

Caution:

It must always be ensured that the supply voltage measured

at the most remote participant does not drop below 18 V DC from the

perspective of the system power supply.

7.6 Diagnostic Display in Integrated Web

Server

The LioN-P modules display the channel and module status as well as the

fault diagnosis on the status page of the integrated web server in clear text

and also in hexadecimal notation. For information on opening the status page,

please refer to the chapters of this manual that follow.

Technical Manual LioN-P PROFINET

Version 2.0 10/2017

Содержание lumberg automation 934 878-001












































































Результаты поиска

Содержание lumberg automation 934 878-001

Отзывы:

Похожие инструкции для lumberg automation 934 878-001

Бренды по названию

Популярные бренды

Belden lumberg automation 934 878-001, Техническое руководство

Результаты поиска

Содержание lumberg automation 934 878-001

Отзывы:

Похожие инструкции для lumberg automation 934 878-001

Бренды по названию

Популярные бренды