Belden lumberg automation 934 878-001 Скачать руководство пользователя страница 33

Страница: 33 / 75

5 Configuration and Startup

5.2 Configuration of LioN-P

PROFINET Modules in TIA Portal

The following options are available

Set Low – Deactivation of output channel (digital value = 0)

Set High – Activation of output channel (digital value = 1)

Hold Last – Holds last output status (digital value corresponds to last

status)

Surveillance Timeout Configuration (ms)

These parameters are provided to all module types with digital outputs. The

configuration can be used to set a delay time (Surveillance Timeout) that

defines the monitoring procedure for the individual digital output currents for

each channel.
The delay time starts after a change to the output channel status. If an output

is activated (rising edge) or deactivated (falling edge) the output monitoring

does not start until the delay time expires. Any fault conditions that arise after

this delay are registered by the diagnosis.
The adjustable value range for the delay time is 0 to 255 ms. The default value

is 80 ms. When the output channel is in the static state, (channel permanently

switched on or off) the value is 100 ms.

IO Mapping Configuration (for 16DI/DO Modules Only)

Configuration of the IO mapping makes it possible to change the data

structure of the I/O data. By default each I/O channel is mapped in sequence

in the process data. Existing PLC programs however, may under certain

circumstances, use another channel assignment.
These parameters enable all I/O channels to be freely assigned a bit in the I/

O data. It should be noted that duplicate assignments are not possible here. If

faulty parameterization of the IO mapping when transferring the configuration

is detected,the LioN-P module registers a fault.

5.2.5 Fast Start-Up (FSU) / Prioritized Start-Up

The LioN-P modules with Fast Start-Up (FSU) support an optimized system

start-up. This guarantees a faster restart after the power supply is restored.
Fast Start-Up can be activated for the LioN-P modules with

PROFINET

interface [X1]

Advanced options

Interface options

over

Prioritized start-

Technical Manual LioN-P PROFINET

Version 2.0 10/2017

Содержание lumberg automation 934 878-001












































































Результаты поиска

Содержание lumberg automation 934 878-001

Отзывы:

Похожие инструкции для lumberg automation 934 878-001

Бренды по названию

Популярные бренды

Belden lumberg automation 934 878-001, Техническое руководство

Результаты поиска

Содержание lumberg automation 934 878-001

Отзывы:

Похожие инструкции для lumberg automation 934 878-001

Бренды по названию

Популярные бренды