background image

Typical Situations

7 Configuration in Typical Situations

Although routers have wide variety of uses, they are commonly used in the following ways.

All the examples below are for IPv4 networks.

7.1 Access to the Internet from LAN

Figure 84: Access to the Internet from LAN – sample topology

In this example, a LAN connecting to the Internet via a mobile network, the SIM card with

a data tariff has to be provided by the mobile network operator. This requires no initial con-
figuration. You only need to place the SIM card in the

SIM1

slot (Primary SIM card), attach

the antenna to the

ANT

connector and connect the computer (or switch and computers) to the

router’s eth0 interface (LAN). Wait a moment after turning on the router. The router will connect
to the mobile network and the Internet. This will be indicated by the LEDs on the front panel of
the router (

WAN

and

DAT

).

Additional configuration can be done in the

LAN

and

Mobile WAN

items in the

Configuration

section of the web interface.

LAN configuration

The factory default IP address of the router’s eth0 interface is in the form

of 192.168.1.1. This can be changed (after login to the router) in the

LAN

item in the

Configura-

tion

section. (See Figure

85

.) In this case there is no need of any additional configuration. The

DHCP server

is also enabled by factory default (so the first connected computer will get the

192.168.1.2 IP address etc.). Other configuration options are described in the Chapter

4.1

.

Mobile WAN Configuration

Use the

Mobile WAN

item in the

Configuration

section to config-

ure the connection to the mobile network. (Fig.

86

.) In this case (depending on the SIM card)

the configuration form can be blank. But make sure that

Create connection to mobile network

is checked (this is the factory default). For more details, see Chapter

4.3.1

.

To check whether the connection is working properly, go to the

Mobile WAN

item in the

Status

section. You will see information about operator, signal strength etc. At the bottom,

you should see the message:

Connection successfully established

. The

Network

item should

134

UM Configuration OWL LTE M12

Rel. 06.1.09 - 07/2019

Содержание Hirschmann OWL LTE M12


























































































































































Отзывы: