Bedfont NOxBOX mobile Скачать руководство пользователя страница 68

Страница: 68 / 84

On completion of last instruction screen, system

will purge and shutdown safely ready for storage.

Alarm band and sound will be heard on shutdown.

NOTE: Alarm band and sound will be heard on

shutdown. System should be stored attached

to suitable mains supply.

7 MAINTENANCE AND REPAIR

WARNING: Maintenance and repair of the BEDFONT NOxBOX

system involves potentially hazardous procedures. Only trained

and qualified personnel who have read and understood the

instructions in this manual shall work on this equipment. Wear

appropriate PPE, and, if applicable, turn off the power before

performing any installation, maintenance, repair, or troubleshooting

procedures.

WARNING: NOxBOX

gas regulators can only be serviced and

repaired by the manufacturer or suitably qualified engineers

working in appropriate conditions who have undergone formal

training with BPR Medical. Regulators are safety critical devices. No

tools should be used on these devices for any reason.

CAUTION: Never bypass safety devices, and never operate the

equipment outside its specified limits.

CAUTION: Check all safety devices at least annually or as otherwise

required by local codes or manufacturer recommendations.

Properly maintain safety valves. Never bypass safety devices, and

never operate the equipment outside its specified limits.

All repairs and component replacements must be undertaken by a

suitably qualified Service Engineer. Please contact your supplier for

service advice and support. The system may only be serviced and

repaired in accordance with the maintenance written instructions

provided by Bedfont Scientific Ltd. The system should not in any

way be altered without approval from the manufacturer. All

replacement components must be approved for use with the

system. The system user has sole responsibility for any

malfunction that arises from improper use, incorrect maintenance,

faulty repair, damage or alteration by any individual not qualified by

Bedfont Scientific Ltd to undertake these measures.

The NOxBOX

system must be subject to regular service inspection and maintenance routines

as defined within this Technical Guide. A faulty or defective system should not be used. System

components that are damaged, broken, missing, visibly worn, deformed, or contaminated should

be replaced or repaired immediately.

Содержание NOxBOX mobile





















































































Результаты поиска

Содержание NOxBOX mobile

Отзывы:

Похожие инструкции для NOxBOX mobile

Бренды по названию

Популярные бренды

Bedfont NOxBOX mobile, Техническое руководство

Результаты поиска

Содержание NOxBOX mobile

Отзывы:

Похожие инструкции для NOxBOX mobile

Бренды по названию

Популярные бренды