Bedfont NOxBOX mobile Скачать руководство пользователя страница 26

Страница: 26 / 84

4.4 Connecting NO Gas Cylinders

Using the on-screen Quick

Start Guide (QSG)

instructions set up the

system as follows:

NOTE: for experienced users, the

“Skip to System Tests” button will

bypass the on-screen QSG and

skip to system setup tests).

Alternatively the “skip to dose”

button will bypass both on-screen

QSG and the system test.

See Chapter 6.3 for detailed

instructions for using the touch

screen interface.

Check that the

NOxBOX

NO cylinder

concentration matches

the value shown on the

system screen. This is

the value upon which

delivery calculations

will be based.

Do not use

any supply cylinder that

does not match this

value

If there is a problem,

contact your Service

Engineer to resolve before

attempting to deliver NO to

a patient.

Check the regulator

sealing surfaces and

connector thread. If your

model has non-metal

sealing elements, ensure

that they are present and

undamaged, showing no

cracks, pock-marks, etc.

1000

Содержание NOxBOX mobile





















































































Результаты поиска

Содержание NOxBOX mobile

Отзывы:

Похожие инструкции для NOxBOX mobile

Бренды по названию

Популярные бренды

Bedfont NOxBOX mobile, Техническое руководство

Результаты поиска

Содержание NOxBOX mobile

Отзывы:

Похожие инструкции для NOxBOX mobile

Бренды по названию

Популярные бренды