Bedfont NOxBOX mobile Скачать руководство пользователя страница 70

Страница: 70 / 84

Follow these precautions when cleaning the NOxBOX

System:

•

The sensors inside the system can be damaged by exposure to alcohol or volatile organic

compound (VOC) spray or fumes. Do not use alcohol- or VOC- based cleaners on this

system. Alcohol-free instrument cleaning wipes are available from Bedfont that are

suitable for cleaning the NOxBOX

system monitor.

•

Clean external surfaces and the touchscreen panel using a damp, soft, lint-free cloth.

•

Do not spray or splash cleaning fluids directly onto the system surfaces. Apply cleaning

fluids with a clean soft lint-free cloth, and avoid excessive wetting of the system. Take

extra care around all connectors to prevent fluid from entering and damaging the system.

•

Only use mild soap and water or an approved disinfectant for cleaning the NOxBOX

System. Always follow manufacturer’s recommendations when using any disinfectant.

•

Do not clean the system with organic solvents, glass cleaner, petroleum-based solvents,

alcohol, or acetone-based solvents.

•

Do not autoclave or gas-sterilize the system.

•

Do not use any abrasive cleaning pads or cleansing fluids on the NOxBOX

system, and

take particular care not to scratch the touchscreen panel.

•

To prevent damage to the touchscreen, avoid excessive pressure when cleaning the touch

screen panel.

•

Ensure that the system is completely dry before returning it to use after cleaning.

Alcohol-free instrument wipes approved for use with the NOxBOX

system are available

from Bedfont Scientific Ltd.

7.4 Calibration

CAUTION: Temperature may affect the accuracy of the NOxBOX

monitoring function. The instrument should be calibrated at the

temperature at which it is expected to be used.

CAUTION: In order to correctly calibrate the NOxBOX

, ensure that

the pump flow is checked and if necessary adjusted prior to

performing sensor calibrations.

CAUTION: Always perform a sensor zero calibration before

performing the full-scale calibration.

7.3 Cleaning the NOxBOX

System

WARNING: Ensure that the unit is turned off and the power cord is

completely disconnected before cleaning the

NOxBOX

System.

Содержание NOxBOX mobile





















































































Результаты поиска

Содержание NOxBOX mobile

Отзывы:

Похожие инструкции для NOxBOX mobile

Бренды по названию

Популярные бренды

Bedfont NOxBOX mobile, Техническое руководство

Результаты поиска

Содержание NOxBOX mobile

Отзывы:

Похожие инструкции для NOxBOX mobile

Бренды по названию

Популярные бренды