Beckhoff EL3182 Скачать руководство пользователя страница 139

Страница: 139 / 145

Appendix

EL3182

139

Version: 1.2

• Select the file (*.rbf) with the new FPGA firmware, and transfer it to the EtherCAT device:

• Wait until download ends

• Switch slave current less for a short time (don't pull under voltage!). In order to activate the new FPGA

firmware a restart (switching the power supply off and on again) of the EtherCAT device is required.

• Check the new FPGA status

NOTE

Risk of damage to the device!

A download of firmware to an EtherCAT device must not be interrupted in any case! If you interrupt this
process by switching off power supply or disconnecting the Ethernet link, the EtherCAT device can only be
recommissioned by the manufacturer!

8.3.5

Simultaneous updating of several EtherCAT devices

The firmware and ESI descriptions of several devices can be updated simultaneously, provided the devices
have the same firmware file/ESI.

Fig. 142: Multiple selection and firmware update

Select the required slaves and carry out the firmware update in BOOTSTRAP mode as described above.

Содержание EL3182


















































































































































Результаты поиска

Содержание EL3182

Отзывы:

Похожие инструкции для EL3182

Бренды по названию

Популярные бренды

Beckhoff EL3182, Документация

Результаты поиска

Содержание EL3182

Отзывы:

Похожие инструкции для EL3182

Бренды по названию

Популярные бренды