BEC MX-210NPV Скачать руководство пользователя страница 92

Страница: 92 / 114

Device Configuration

Access Management – Packet Filter (IP & MAC Filter)

BEC MX-210NPV User Manual

Packet Filter

You can filter the packages by MAC address, IP address, Protocol, Port number and Application or
URL.

❖

Filter Type - IP & MAC Filter

IP & MAC Filter Editing

Rule Index:

The numeric rule indicator.

Individual Active:

Yes

to enable the rule.

Action:

This is how to deal with the packets matching the rule. Allow please select White List or Black

selecting Black List.

Interface:

Select to determine which interface the rule will be applied to.

Direction:

Select to determine whether the rule applies to outgoing packets, incoming packets or

packets of both directions.

Type:

Choose type of field you want to specify to monitor. Select “IPv4” for IPv4 address, port number

and protocol. Select “IPv6” for IPv6 address, port number and protocol. Select “MAC” for MAC address.

Содержание MX-210NPV



















































































































Результаты поиска

Содержание MX-210NPV

Отзывы:

BEC MX-210NPV, Руководство пользователя, Страница: 92 / 114

Результаты поиска

Содержание MX-210NPV

Отзывы: