BEC MX-210NPV Скачать руководство пользователя страница 52

Страница: 52 / 114

Device Configuration

Interface Setup – Internet (EWAN)

BEC MX-210NPV User Manual

IGMP Proxy:

IGMP (Internet Group Multicast Protocol) is a network-layer protocol used to establish

membership in a Multicast group. Choose whether enable IGMP proxy.

IPv6 options

(only when choose IPv4/IPv6 or just IPv6 in IP version field above):

IPv6 Address:

Type the WAN IPv6 address from your ISP.

Obtain IPv6 DNS:

Choose if you want to obtain DNS automatically.

Primary/Secondary:

if you choose Disable in the Obtain IPv6 DNS field, please type the exactly

primary and secondary DNS.

MLD Proxy:

MLD (Multicast Listener Discovery Protocol) is to IPv6 just as IGMP to IPv4. It is a

Multicast Management protocol for IPv6 multicast packets.

When router’s Internet configuration is finished successfully, you can go to status to get the connection
information.

Click

Save

to apply settings.

Содержание MX-210NPV



















































































































Результаты поиска

Содержание MX-210NPV

Отзывы:

BEC MX-210NPV, Руководство пользователя, Страница: 52 / 114

Результаты поиска

Содержание MX-210NPV

Отзывы: