BEC MX-210NPV Скачать руководство пользователя страница 13

Страница: 13 / 114

Product Overview

Device Description (Rear Panel Connectors)

BEC MX-210NPV User Manual

Rear Panel Connectors

INTERFACE

MEANING

4G/LTE Antenna
Connectors
(Main/Aux)

SMA female connectors.

Manually screw the cellular antennas tight to the female connectors.

Connect to

Main

if decide to use one antenna instead of two.

2 Power Source

Power ON/OFF switch

(1) with Power Switch ON:

power up by the supplied DC power adapter

(

2) with Power Switch OFF:

power up by the PoE battery unit

Power Jack

(DC IN)

Connect the supplied Power Adapter to this jack.

4 Rest

After the device is powered on, press it

6 seconds or above

: to restore to factory default

settings (this is used when you cannot login to the router, e.g. forgot your password)

Gigabit Ethernet

(LAN 1 / PoE)

Ethernet LAN

: Connected to an Gigabit (1000Mbps) Ethernet device

Ethernet PoE

Connect with a 802.3at Gb PoE injector to provide power to the MX-210NPV

Gigabit Ethernet

(LAN 1 / EWAN)

Ethernet LAN

: Connected to an Gigabit (1000Mbps) Ethernet device

Ethernet WAN

: Software configurable in the GUI. Connected with a broadband connection

device

7 SIM Card Slot

Insert the mini SIM card (2FF) with the gold contact facing down.

Push the mini SIM card (2FF) inwards to eject it

* Power off the MX-210NPV before inserting or removing the SIM card(s)

Содержание MX-210NPV



















































































































Результаты поиска

Содержание MX-210NPV

Отзывы:

BEC MX-210NPV, Руководство пользователя, Страница: 13 / 114

Результаты поиска

Содержание MX-210NPV

Отзывы: