BEC MX-210NPV Скачать руководство пользователя страница 8

Страница: 8 / 114

Introduction

Features & Specifications

BEC MX-210NPV User Manual

Features & Specifications

• 4G/LTE and/or Ethernet IP broadband connectivity

• High performance SX antenna for increased coverage, signal reception and efficiency

• Versatile Gigabit LAN & Ethernet WAN (GbE WAN) for Cable/Fiber/xDSL high WAN throughput

• Verstalile Gigabit LAN & PoE

• Firewall Security with DoS Preventing and Packet Filtering

• Quality of Service Control for traffic prioritization management

• Universal Plug and Play (UPnP) Compliance

• Ease of Use with Quick Installation Wizard

• Small form factor with multiple mounting options, easily installed by a single person

Availability and Resilience

• Dual-WAN Interfaces

• Auto fail-over and failback

• High performance external antennas

Network Protocols and Features

• IPv4, IPv6, IPv4 / IPv6 dual stack

• IP Tunnel IPv6 in IPv4 (6RD)

• IP Tunnel IPv4 in IPv6 (DS-Lite)

• NAT, static routing and RIP-1/2

• Universal Plug and Play (UPnP) compliant

• Dynamic Domain Name System (DDNS)

• Virtual server and DMZ

• SNTP, DNS relay

• IGMP proxy and IGMP snooping

• MLD proxy and MLD snooping

• Supports port-based Virtual LAN (VLAN)

Firewall

• Built-in NAT Firewall

• Stateful Packet Inspection (SPI)

• DoS attack prevention including Land Attack, Ping of Death, etc.

Содержание MX-210NPV



















































































































Результаты поиска

Содержание MX-210NPV

Отзывы:

BEC MX-210NPV, Руководство пользователя, Страница: 8 / 114

Результаты поиска

Содержание MX-210NPV

Отзывы: